- Downloads
- Sounds
- projects.esu.eu
- Search results
Athearn SD70ACU LokSound 5 North American & Australian factory Equipped Sound files 
H0 N XL L M4
- Article numbers:12493.1, 12493.2
- Last change: 1/28/2022
- Manufacturer: Athearn
This file is custom mapped for the Athearn SD70ACU Locomotives using a 58429 ESU LokSound 21MTC decoder and the factory Athearn Motherboards.
As there are 2 different startups on the SD70ACU, Air Start for NS and Electric Start for CP, we have created a file for each version:
12493.1 Canadian Pacific Electric Start Version with Nathan K3L Horn
12493.2 Norfolk Southern Air Start Version with Nathan K5LA Horn
In some cases the railroads varied on horns. Please use the list below to set the appropriate horn and bell for your roadname using CV163 and CV164.
The EMD SD70ACU is a 6-axle 4,300 hp (3,200 kW) diesel-electric locomotive originally built by General Motors Electro-Motive Division as an SD9043MAC, and rebuilt by Norfolk Southern and Progress Rail. They are operated by two railroads, Norfolk Southern railway and Canadian Pacific.
The SD70ACU began under Norfolk Southern, who rebuilt its EMD SD90MACs to this configuration at its shops in Altoona, Pennsylvania. The first locomotive entered the rebuilding process in September 2015, which was number 7299. As of 2019, all 110 units have been released into active service.
All of the SD70ACUs will be rebuilt with the latest EMD cab which meets current FRA crashworthiness standards. The Siemens electronics will be replaced with Mitsubishi electronics. The rebuild also includes the installation of Ultra Cab II, locomotive speed limiter (LSL), and cab signals. The trucks will be rebuilt only as needed and they are not getting traction motors swapped out.
In 2018, Canadian Pacific started a similar rebuild program with its long dormant SD90MAC fleet. Unlike NS, the work on these rebuilds was not be done in-house, but by Progress Rail at its Mayfield, Kentucky and Muncie, Indiana facilities.
In early 2021 CP bought 40 more SD90MACs from Union Pacific to continue the SD70ACU rebuild program. Some CP-patched, ex-Union Pacific SD90MACs have already been seen heading to Canada prior to rebuilding.
While not directly recorded from a SD70ACU we believe this to be an accurate representation using very similar recordings.
This project is a special notch based low idle with an automatic high idle version. It has a single turbo late (silenced) exhaust stack.
This ESU Sound file will operate like the prototype in terms of throttle notching. You will notice there is low and high idle, and once above notch 3 and back to Idle the prime mover will stay up in high idle for a period of time. Once in low idle throttling up to notch 1 or notch 2 and return to idle will stay in low idle.
File also contains an "Isolation Switch" Mode on F15 when Standing Still.
Pressing F15 while not moving will lower the prime mover to a "Low Idle" and lock the motor. F15 must be turned off to begin moving.
Another Mode is "Reverser In Center Position". When pressing F24 while stopped, the motor will lock so you can throttle through the notches like the prototype in neutral. F24 must be turned off to begin moving.
This project has "Run 8" mode. When turning on F26 with F28 off, the prime mover goes to run 8. Turning off F26 returns the prime mover sounds back to normal mode.
This project has "Coast" mode. When turning on F27 with F28 off, the prime mover goes to idle for coasting purposes. Turning off F27 returns the prime mover sounds back to normal mode.
You can still use F26 and F27 for manual nothing. You have to keep both F26 and F27 off before pressing F28 to turn on manual notching. Once F28 is on, you can use F26 to notch up and F27 to notch down. F26, F27, and F28 must be turned off to return to normal mode.
This project has "Load" mode. When turning on F29 with F15, F24, F26, F27, F28 off, the prime mover goes into load mode. While you are using load mode, the prime mover will notch up 1 or more notches based on primary load settings(CV104). The throttle notches up using speed instead of requested speed while using the load feature. F29 must be turned off to return to normal mode.
This file is also equipped with a Smart Start feature that cycles the prime mover on and off at intervals of your choice if the throttle is left at Idle and the loco is stopped.
Smart Start (Sound CV14):
CV168=0 No Smart Start Cycle - Default
CV168=1 - 3 Minute Cycle
CV168=2 - 6 Minute Cycle
CV168=3 - 9 Minute Cycle
CV168=4 - 12 Minute Cycle
Etc.....
CV168=255 - 765 Minute Cycle
3rd Gen Horn Pack 1
Horns (SoundCV9):
CV163=0 Leslie S-3L-R
CV163=1 Leslie S-5T-RRO-R
CV163=2 Nathan K-2H
CV163=3 Nathan K-3H-L
CV163=4 Nathan K-3L
CV163=5 Nathan K-3LA
CV163=6 Nathan K-5HL
CV163=7 Nathan K-5H-R24
CV163=8 Nathan K-5L
CV163=9 Nathan K-5LA
CV163=10 Nathan K-5LA-R24
CV163=11 Nathan K-5L-LA
CV163=12 Nathan K-5L-R24
CV163=13 Nathan P-3
CV163=14 Nathan P-5-R24
EMD 3rd Generation Bell Template Pack 2
Bells (SoundCV10):
CV164=0 EMD 8475495 Steel Bell 049
CV164=1 EMD 8475495 Steel Bell 066
CV164=2 EMD 8475495 Steel Bell 068
CV164=3 Graham-White E-Bell 006
CV164=4 Graham-White E-Bell 009
Auto Bell:
Many Second and Third Generation locomotives have been fitted with an Automatic Bell that is triggered when the horn is blown. In MANY cases this cannot even be bypassed on modern locos. Before the FRA mandated this feature on new locomotives the bell was of course turned on and off separately. Some locomotives were delivered with a manual bell and have been converted to an automatic bell. This creates a challenge in sound file creation.
We realize that not every loco with a particular prime mover had this feature. As such we have built in an option to turn the feature on and off. We will set the default in the file to be what is most appropriate for the particular file.
To turn the feature OFF - Auto Bell OFF:
1. Remove the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 4
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 0
To turn the feature ON - Auto Bell ON:
1. ADD the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 12
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 1
Auto Bell Timer:
The Bell timer is amount of time the bell will play after the horn if the auto timer is active. The timer is broken down into 1/4 of a second increments.
CV169=4 - 1 Second
CV169=8 - 2 Seconds
CV169=12 - 3 Seconds
CV169=16 - 4 Seconds
CV169=20 - 5 Seconds - Default
Etc...
3rd Generation Brake Squeal Template Pack 1
Brake Squeal (SoundCV11)
CV165=0 Composition Shoe #1
CV166=1 Composition Shoe #2
EMD 3rd Generation Air Dryer Template Pack 1
Air Dryer (SoundCV12)
CV166=0 GP60 Air Dryer 1
CV166=1 SD60E Air Dryer 2
CV166=2 SD70M-2 Air Dryer 3
CV166=3 SD70MAC Air Dryer 4 Hide description more…
H0 N XL L M4
- Article numbers
- 12493.1, 12493.2
- Last change
- 1/28/2022
- Manufacturer
- Athearn
ALCO 12cyl 244 (FT) LokSound Select Retail Soundfiles H0 N XL L M4
- Article numbers:73401, 73801, 73301
- Last change: 9/30/2016
- Manufacturer: ESU electronic solutions ulm
Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.4.21 or newer
The American Locomotive Company's model 244 prime mover was developed during the mid-1940s to power its post-war diesel locomotives. Interestingly, while Alco helped pioneer diesel technology dating back to the 1920s it had difficulty truly competing against Electro-Motive-Division due to reliability issues with its diesel engines. Before Alco began implementing the 244 in its locomotives the builder had spent most of the 1930s developing an earlier model that was used in most of its early switchers. The new prime mover was supposed to usher in a new era for Alco but instead saw it slip further behind EMD in the marketplace. During the early 1950s the manufacturer replaced the engine with the more reliable 251 that powered its Century series. It would prove to be the company's last engine as it exited the market before 1970.
This sound file would be appropriate for the following locomotives:
RS-2
RS-3
RSC-2
RSC-3
RSD-4
RSD-5
Although there are slight differences, this sound file could also be used in the following locomotives:
FA-1
FB-1
FA-2
FB-2
FPA-2
FPB-2
As with all SELECT decoders there are up to 16 separate horns, 2 separate brake squeals and 2 bells included on this one sound profile! All changeable using CV48.
Prime Mover:
CV48=0 ALCO 12cyl 244
Uses our OLD-HORNS-AND-BELLS template...
Horns:
CV48=0 Nathan Single Chime
CV48=1 Nathan K3L
CV48=2 Nathan M5
CV48=3 Nathan P3
CV48=4 Nathan Old Cast P5
CV48=5 Nathan K3HA
CV48=6 Leslie RS3L
CV48=7 Leslie S3L #1
CV48=8 Leslie A125
CV48=9 Leslie A200
CV48=10 Leslie RS3K
CV48=11 Hancock Air Whistle
CV48=12 Wabco E2
CV48=13 Nathan M3H
CV48=14 Leslie S2M
CV48=15 Leslie Dual A125-A200
Bells:
CV48=0 Steel Bell
CV48=64 ALCO Bronze Bell
Add values from above for total CV48 value.
Default CV48 Value = 64
0 - ALCO 12cyl 244
0 - Nathan Single Chime
64 - ALCO Bronze Bell
Total 0+0+64 = 64
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/ Hide description more…
H0 N XL L M4
- Article numbers
- 73401, 73801, 73301
- Last change
- 9/30/2016
- Manufacturer
- ESU electronic solutions ulm
EMD 16cyl 645E3 (FT) LokSound Select Retail Soundfiles H0 N XL L M4
- Article numbers:73408, 73808, 73308
- Last change: 9/30/2016
- Manufacturer: ESU electronic solutions ulm
Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.4.21 or newer
The emd 645 series was an evolution of the earlier 567 series and a precursor to the later 710 series. When the 645 prime mover entered production in 1965, a large series of new locomotive models was introduced. The turbocharged version was used in EMD's 40 Series (GP40, SD40 and SD45) in 3,000 horsepower (2,200 kW), sixteen-cylinder form and in 3,600 horsepower (2,700 kW), twenty-cylinder form. EMD also introduced the Roots-blown 38 Series (GP38, SD38) and turbocharged, twelve-cylinder 39 Series (GP39, SD39). All of these locomotive models extensively share common components and subsystems, thereby significantly reducing cost and increasing interchangeability. The GP38-2 and SD40-2 became the most popular models of the series and among the most popular locomotive models ever built.
This 16cyl 645E3 with Turbo sound file would be appropriate for the following locomotives:
GP40
GP40P
GP40P-2
GP40-2
GP40X
SD40X
SD40A
SD45T-2
SD40-2
SD40-2W
SD40-2S
F40C
F40PH
F40PH-2
F40PH-2M
SDP40F
SD40-2F
Export locomotives:
GT26MC
GT26CW
GT26CW-1
GT26CW-2
GT26CU-2
Please note:
This file contains a "Class Light" feature which allows for Cycling Aux3, Aux4, and Aux5 when using a 21MTC decoder. Assign the "Class Light" "Sound" to the function button of your choice and and be sure each Aux listed above is set to "Dimmable Headlight".
As with all SELECT decoders there are up to 16 separate horns, 2 separate brake squeals and 2 bells included on this one sound profile! All changeable using CV48.
Prime Mover:
CV48=0 EMD 16cyl 645E3
Uses our INTERMEDIATE-HORNS-AND-BELLS template...
Horns:
CV48=0 Nathan K5LA
CV48=1 Nathan K3L
CV48=2 Nathan M5
CV48=3 Nathan P3
CV48=4 Nathan Old Cast P5
CV48=5 Nathan K3H
CV48=6 Leslie RS3L
CV48=7 Leslie RS5T
CV48=8 Leslie A125
CV48=9 Nathan M3
CV48=10 Leslie RS3K
CV48=11 Nathan K5H
CV48=12 Leslie A-125
CV48=13 Nathan M3H
CV48=14 Leslie S3E
CV48=15 Leslie S5TRF
Bells:
CV48=0 EMD Steel Bell
CV48=64 EMD Bronze Bell
Add values from above for total CV48 value.
Default CV48 Value = 69
0 - EMD 16cyl 645E3
7 - Nathan K3H
64 - EMD Bronze Bell
Total 0+5+64 = 69
Please Note:
File Contains a Modern E-Bell, and MILW E-Bell and a Gong Bell which can be selected in Function Mapping. Simply choose the appropriate Sound Slot for F1.
Sound Slot 4 is the default bell (changable with CV48)
Sound Slot 9 is the Modern E-Bell
Sound Slot 22 is the MILW E-Bell
Sound Slot 23 is the Gong Bell
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/ Hide description more…
H0 N XL L M4
- Article numbers
- 73408, 73808, 73308
- Last change
- 9/30/2016
- Manufacturer
- ESU electronic solutions ulm
ALCO 6cyl 539T (FT) LokSound Select Retail Soundfiles H0 N XL L M4
- Article numbers:73411, 73811, 73311
- Last change: 9/30/2016
- Manufacturer: ESU electronic solutions ulm
Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.4.21 or newer
The ALCO 539 engine was developed in response to the perceived drawback that ALCO's line of diesel switchers had a restricted field of vision because of the high hood. Both Baldwin and EMC were offering diesel switchers with a lower engine hood that the trainmen could see over.
The 539T was equipped with the Buchi turbocharger, being made under license by the Elliott Manufacturing Company of Jeannette, Pennsylvania. The first 539T engines were used in S-2 switchers and DL-105 passenger locomotives built in September 1940.
ALCO Locomotives:
S-2
S-4
RS-1
RSC-1
RSD-1
DL-105
DL-107
DL-108
DL-109
DL-110
MLW Locomotives:
S-2
S-4
S-7
S-12
RS-1
RSC-13
As with all SELECT sound files, this file contains up to 16 different horns, 2 bells and 2 brake squeals.
Prime Mover:
CV48=0 ALCO 6cyl 539T
Uses our OLD-HORNS-AND-BELLS template...
Horns:
CV48=0 Nathan Single Chime
CV48=1 Nathan K3L
CV48=2 Nathan M5
CV48=3 Nathan P3
CV48=4 Nathan Old Cast P5
CV48=5 Nathan K3HA
CV48=6 Leslie RS3L
CV48=7 Leslie S3L #1
CV48=8 Leslie A125
CV48=9 Leslie A200
CV48=10 Leslie RS3K
CV48=11 Hancock Air Whistle
CV48=12 Wabco E2
CV48=13 Nathan M3H
CV48=14 Leslie S2M
CV48=15 Leslie Dual A125-A200
Bells:
CV48=0 Steel Bell
CV48=64 ALCO Bronze Bell
Add values from above for total CV48 value.
Default CV48 Value = 64
0 - PRIME MOVER - ALCO 6cyl 539T
0 - HORN - Nathan Single Chime
64 - BELL - ALCO Bronze Bell
Total 0+0+64 = 64
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/ Hide description more…
H0 N XL L M4
- Article numbers
- 73411, 73811, 73311
- Last change
- 9/30/2016
- Manufacturer
- ESU electronic solutions ulm
GE GEVO-12 (FT) LokSound Select Retail Soundfiles H0 N XL L M4
- Article numbers:73423, 73823, 73323
- Last change: 10/1/2016
- Manufacturer: ESU electronic solutions ulm
Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.4.21 or newer
GE Evolution 12cyl "GEVO" locomotives have a 4 stoke diesel engine and have been designed to be more efficient and more emission friendly than previous models. Evolution Series locomotives are equipped with either AC or DC traction motors, depending on the customer's preference, though admittedly there is little sound difference if any between the two.
All early GEVOs had been delivered with the Nathan Airchime K5HL air horn. Later GEVOs started to recieve a slightly different K5HLL horn. Both are inlcuded with the file. Most if not all have been delivered with a Graham-White 373 E-Bells. This E-Bell is tied to the horn circuit in the locomotive and will play automatically when the horn is played. The ESU version also has this new feature. The bell can be activated by either pressing F1 or by pressing the horn using F2. The "Auto-Bell" can be turned off by removing the the Auto-Bell sound slot from F2. (CV31 = 16, CV32 = 2, CV319 = 0)
Another feature of the prototype is "Smart Start". For the sake of both emissions and fuel savings, all GEVOs have been built with an auto shutdown/auto start feature. After the loco has been idle for a period time, the engine will shut down on its own. If the prime mover cools to a certain temperature the loco will automatically start again to keep from freezing. Our ESU version is also equipped with this "Smart Start" feature. If enabled, after idling for about 5 minutes the engine will shut down. Without doing anything to the throttle, it will start again on its own depending on options set in CV48. If at any time during this shutdown mode you would like to run your loco, just turn the throttle slightly and the engine will go through its start up cycle and then allow you to move it. The feature can also be turned off if it is deemed undesirable. By default this feature is off.
Though all GEVOs were delivered with Nathan K5HL or K5HLL air horns, we've also included a few extra horns in case you wish to use something different. Due to the vast numbers of sounds included in the file we were not able to include our normal 16 horns, but we have included multiple for your choosing. These are selectable by using CV48.
Prime Mover:
CV48=0 GE GEVO-12 (no "Smart Start")
CV48=16 GE GEVO-12 (3 minute "Smart Start" cycle)
CV48=32 GE GEVO-12 (6 minute "Smart Start" cycle)
CV48=48 GE GEVO-12 (auto shut down, throttle up to start)
Horns:
CV48=0 Nathan K5LA
CV48=1 Nathan Airchime K5HL
CV48=2 Nathan K3
CV48=3 Nathan P3
CV48=4 Nathan Old Cast P5
CV48=5 Nathan K5HLL #1
CV48=6 Nathan K5HLL #2
CV48=7 Nathan K5HL(Duplicate horn due to space restrictions)
CV48=8 Leslie S5T
CV48=9 Nathan K5H
CV48=10 Nathan K5HLL #1 (Duplicate horn due to space restrictions)
CV48=11 Nathan K5H (Duplicate horn due to space restrictions)
CV48=12 Nathan K5H (Duplicate horn due to space restrictions)
CV48=13 Nathan K5H (Duplicate horn due to space restrictions)
CV48=14 Nathan K5H (Duplicate horn due to space restrictions)
CV48=15 Nathan K5H (Duplicate horn due to space restrictions)
Bells:
CV48=0 GE Fast Steel Bell
CV48=64 Modern E-Bell - Default
Add values from above for total CV48 value.
Default CV48 Value = 0
0 - GE GEVO-12 (no "Smart Start")
1 - Nathan Airchime K5HL
64 - Modern E-Bell
Total 0+1+64 = 65
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/ Hide description more…
H0 N XL L M4
- Article numbers
- 73423, 73823, 73323
- Last change
- 10/1/2016
- Manufacturer
- ESU electronic solutions ulm
EMD 16cyl 710G3C-T2 (FT) LokSound Select Retail Soundfiles H0 N XL L M4
- Article numbers:73425, 73825, 73325
- Last change: 10/1/2016
- Manufacturer: ESU electronic solutions ulm
Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.4.21 or newer
The EMD 710 is a line of diesel engines built by Electro-Motive Diesel (EMD). Introduced in 1985, the 710 series replaced the earlier EMD 645 series. Since its introduction, EMD has continually upgraded the 710G diesel engine. Power output has increased from 3,800 horsepower on 1985's 16-710G3A to 4,500 horsepower on 2012's 16-710G3C-T2. Over the production span of certain locomotive models, upgraded engine models have been fitted when these became available. For example, an early 1994-built SD70MAC had a 16-710G3B, whereas a later 2003-built SD70MAC would have a 16-710G3C-T1.
In 2005 EMD was released a Tier 2 710 prime mover for thier upcoming SD70M-2 and SD70ACe models. The SD70M-2 is a DC traction version of the SD70ACe, and the two models are nearly identical in every other respect. Like the SD70ACe, the SD70M-2 models are equipped with the 16-710G3C-T2 prime mover which is rated at 4,300 horsepower. One of the main differences in the SD70M-2/SD70ACes from previous SD70s is the addition of Air Start. This loud burst of air in the start sequence is not present on most earlier EMD locomotives. All SD70M-2s and SD70ACes, except for the ones bought by CITX, are equipped with the Airchime model K5LLA air horn and an electronic bell. Due to this Air Start these locomotives have a period of High Idle just after start up to recharge the air and warm up the locomotive.
Another feature of the prototype is "Smart Start". For the sake of both emissions and fuel savings all SD70M-2s and SD70ACes have been built with an auto shutdown/auto start feature. After the loco has been idle for a period time, the engine will shut down on its own. If the prime mover cools to a certain temperature the loco will automatically start again to keep from freezing. Our ESU version is also equipped with this "Smart Start" feature. If enabled, after idling for about 5 minutes, the engine will shut down and without doing anything to the throttle it will start again on its own depending on options set in CV48. If at any time during this shutdown mode you would like to run your loco, just turn the throttle slightly and the engine will go through it's start up cycle and then allow you to move it. The feature can also be turned off if it is deemed undesirable. By default this feature is off.
Locomotives:
SD70M-2
SD70ACe
As these locomotives were almost always fitted with Nathan AirChime K5LLA airhorns, we've provided 6(!) versions of this horn on this sound file.
Prime Mover:
CV48=0 EMD 16cyl 710G3C-T2 (no "Smart Start")
CV48=16 EMD 16cyl 710G3C-T2 (3 minute "Smart Start" cycle)
CV48=32 EMD 16cyl 710G3C-T2 (6 minute "Smart Start" cycle)
CV48=48 EMD 16cyl 710G3C-T2 (auto shut down, throttle to up to start)
Horns:
CV48=0 Nathan K5LA
CV48=1 Nathan K5LLA #1
CV48=2 Nathan K5LLA #1 (Duplicate horn due to space restrictions)
CV48=3 Nathan K5LLA #2
CV48=4 Nathan Old Cast P5
CV48=5 Nathan K5LLA #3
CV48=6 Nathan K5LLA #4
CV48=7 Nathan K5LLA #5
CV48=8 Nathan K5H
CV48=9 Nathan K5LLA #6
CV48=10 Nathan K5HL
CV48=11 Nathan K5HLL #1
CV48=12 Nathan K5HLL #2
CV48=13 Nathan K5LLA #4 (duplicate - space restriction)
CV48=14 Nathan K5LLA #4 (duplicate - space restriction)
CV48=15 Nathan K5LLA #4 (duplicate - space restriction)
Bells:
CV48=0 Steel Bell
CV48=64 Modern E-Bell
Add values from above for total CV48 value.
Default CV48 Value = 70
0 - EMD 16cyl 710G3C=T2
6 - Nathan K5LLA #4
64 - Modern E-Bell
Total 0+6+64 = 70
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/ Hide description more…
H0 N XL L M4
- Article numbers
- 73425, 73825, 73325
- Last change
- 10/1/2016
- Manufacturer
- ESU electronic solutions ulm
EMD 16cyl 645E (FT) LokSound Select Retail Soundfiles H0 N XL L M4
- Article numbers:73426, 73826, 73326
- Last change: 9/30/2016
- Manufacturer: ESU electronic solutions ulm
Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.4.21 or newer
The EMD 645 family of diesel engines were designed and manufactured by the Electro-Motive Division of General Motors. The 645 series was an evolution of the earlier 567 series and a precursor to the later 710 series. The 645 series engines entered production in 1965. All 645 engines utilize forced induction, with either a Roots blower or a turbocharger. The 645 series has a maximum engine speed of between 900 and 950 revolutions per minute (rpm), an increase over the 800 to 900 rpm maximum speed for the 567 series.
Locomotives:
GP38
GP38AC
GP38-2
GP38-2L
GP38-2W
SD38
SD38-2
NSWGR 422 Class
Victorian Railways X Class
EMD G26
As with all SELECT decoders there are up to 16 separate horns, 2 separate brake squeals and 2 bells included on this one sound profile! All changeable using CV48.
Prime Mover:
CV48=0 EMD 16cyl 645E
Uses our INTERMEDIATE-HORNS-AND-BELLS template...
Horns:
CV48=0 Nathan K5LA
CV48=1 Nathan K3L
CV48=2 Nathan M5
CV48=3 Nathan P3
CV48=4 Nathan Old Cast P5
CV48=5 Nathan K3HA
CV48=6 Leslie S3L #1
CV48=7 Leslie RS5T
CV48=8 Leslie A125
CV48=9 Nathan M3
CV48=10 Leslie RS3K
CV48=11 Nathan K5H
CV48=12 Leslie S2M
CV48=13 Nathan M3H
CV48=14 Leslie S3E
CV48=15 Leslie S5TRF
Bells:
CV48=0 Steel Bell
CV48=64 Bronze Bell
Add values from above for total CV48 value.
Default CV48 Value = 71
0 - EMD 16cyl 645E
7 - Leslie RS5T
64 - Bronze Bell
Total 0+7+64 = 71
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/ Hide description more…
H0 N XL L M4
- Article numbers
- 73426, 73826, 73326
- Last change
- 9/30/2016
- Manufacturer
- ESU electronic solutions ulm
EMD 16cyl 710G3A (FT) LokSound Select Retail Soundfiles H0 N XL L M4
- Article numbers:73431, 73831, 73331
- Last change: 9/30/2016
- Manufacturer: ESU electronic solutions ulm
Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.4.21 or newer
The EMD 710 is a line of diesel engines built by Electro-Motive Diesel (EMD). Introduced in 1985, the 710 series replaced the earlier EMD 645 series. Since its introduction, EMD has continually upgraded the 710G diesel engine. Power output has increased from 3,800 horsepower on 1985's 16-710G3A to 4,500 horsepower on 2012's 16-710G3C-T2. Over the production span of certain locomotive models, upgraded engine models have been fitted when these became available. For example, an early 1994-built SD70MAC had a 16-710G3B, whereas a later 2003-built SD70MAC would have a 16-710G3C-T1.
Locomotives:
GP60
GP60M
GP60B
SD60
SD60M
SD60I
SD60F
Austrailian National AN Class
Although recorderd from a GP60, this file would be a close match for the following locomotives:
SD50AF
SD70
SD70M
SD75
SD75I
SD70MAC
SD90MAC
SD50X
and others...
As with all SELECT decoders there are up to 16 separate horns, 2 separate brake squeals and 2 bells included on this one sound profile! All changeable using CV48.
Prime Mover:
CV48=0 EMD 16cyl 710G3A
Uses our NEW-HORNS-AND-BELLS template...
Horns:
CV48=0 Nathan K5LA
CV48=1 Nathan K3L
CV48=2 Nathan M5
CV48=3 Nathan P3
CV48=4 Nathan Old Cast P5
CV48=5 Nathan K3HA
CV48=6 Leslie RS3L
CV48=7 Leslie S3L #1
CV48=8 Leslie S5T
CV48=9 Nathan M3
CV48=10 Leslie RS3K
CV48=11 Leslie A125
CV48=12 Leslie A125 (duplicate - space restriction)
CV48=13 Leslie A125 (duplicate - space restriction)
CV48=14 Leslie A125 (duplicate - space restriction)
CV48=15 Leslie A125 (duplicate - space restriction)
Bells:
CV48=0 Steel Bell
CV48=64 Bronze Bell
Add values from above for total CV48 value.
Default CV48 Value = 71
0 - EMD 16cyl 710G3A
7 - Leslie S3L #1
64 - Bronze Bell
Total 0+7+64 = 71
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/ Hide description more…
H0 N XL L M4
- Article numbers
- 73431, 73831, 73331
- Last change
- 9/30/2016
- Manufacturer
- ESU electronic solutions ulm
FM 6cyl 38D (FT) LokSound Select Retail Soundfiles H0 N XL L M4
- Article numbers:73432, 73832, 73332
- Last change: 1/15/2018
- Manufacturer: ESU
Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.4.21 or newer
As with all SELECT decoders there are up to 16 separate horns, 2 separate brake squeals and 2 bells included on this one sound profile! All changeable using CV48.
Prime Mover:
CV48=0 FM 6cyl 38D
Horns:
CV48=0 Leslie A200 #1
CV48=1 Nathan K3L
CV48=2 Nathan M5
CV48=3 Nathan P3
CV48=4 Nathan Old Cast P5
CV48=5 Nathan K3HA
CV48=6 Leslie S3L #1
CV48=7 Leslie RS5T
CV48=8 Leslie A125
CV48=9 Nathan M3
CV48=10 Leslie RS3K
CV48=11 Nathan K5H
CV48=12 Leslie S2M
CV48=13 Nathan M3H
CV48=14 Leslie S3E
CV48=15 Leslie S5TRF
Bells:
CV48=0 Steel Bell
CV48=64 Bronze Bell
Add values from above for total CV48 value.
Default CV48 Value = 64
0 - FM 6cyl 38D
0 - Nathan P3
64 - Bronze Bell
Total 0+0+64 = 64
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/ Hide description more…
H0 N XL L M4
- Article numbers
- 73432, 73832, 73332
- Last change
- 1/15/2018
- Manufacturer
- ESU
EMD 16cyl 567C (FT) LokSound Select Retail Soundfiles H0 N XL L M4
- Article numbers:73436, 73836, 73336
- Last change: 9/30/2016
- Manufacturer: ESU electronic solutions ulm
Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.4.21 or newer
The EMD 567 16cyl Prime Mover was one of the most widely used Prime Movers in the world! From F-Units to Geeps this popular power house can still be found in many locomotives riding the rails today.
We have provided 2 versions of the prime mover in the sound file.
With Transition and without Manual Transition!
Transition is the process by which the transmission of a diesel-electric locomoitve is brought from series wiring to parallel wiring. When in series, all current in the locomotive pass through all motors: this produces maximum low-speed force in the motors, i.e., maximum starting torque. When in parallel, current is divided among the motors: this produces maximum high-end efficency, i.e., highest motor speed. In the Early EMD 567 prime movers this could be done manually. There was a throttle lever and a transition lever on the control stands. When the engineer made transition there was a very distinct sounds of the prime mover winding down to idle then up again quickly from Idle to the throttle notch. Not all locomotives can make transition -- yard locomotives are often wired only for series. Also many locomotives were equipped with automatic transitions that occured at a high rate of speed. This classic sound of "Manual Transition" is not heard in these engines the same way as it is in the early 567s. In Fact, it is best to check your prototype as this manual transistion sound could arguably be stated to be wrong for more than it is right for! Due to this fact we have made our sound with the ability to switch between these options so you can have the proper prime mover sounds for your prototype. By simply changing 1 CV (CV 48) you can choose one or the other.
As with All Select sound files this contains up to 16 different Horns, including so newly edited ones!
This LokSound Select file contains two versions of the prime mover:
Prime mover #1 (CV48=0) features a "EMD 567 16cyl with Normal Transition"
Prime mover #2 (CV48=16) features a "EMD 567 16cyl with Manual"
Locomotives:
FP7
FP9
FL9
FT
F2
F3
F7
F9
GP7
GP8
GP9
GP10
GP11
BL2
GP18
GP28
SD7
SD9
SD18
SD28
As with all SELECT decoders there are up to 16 separate horns, 2 separate brake squeals and 2 bells included on this one sound profile! All changeable using CV48.
Prime Mover:
CV48=0 EMD 16cyl 567C with Normal Transistion
CV48=16 EMD 16cyl 567C with Manual Transistion
Uses our OLD-HORNS-AND-BELLS template...
Horns:
CV48=0 Nathan Single Chime
CV48=1 Nathan K3L
CV48=2 Nathan M5
CV48=3 Nathan P3
CV48=4 Nathan Old Cast P5
CV48=5 Nathan K3HA
CV48=6 Leslie RS3L
CV48=7 Leslie S3L #1
CV48=8 Leslie A125
CV48=9 Leslie A200
CV48=10 Leslie RS3K
CV48=11 Hancock Air Whistle
CV48=12 Wabco E2
CV48=13 Nathan M3H
CV48=14 Leslie S2M
CV48=15 Leslie Dual A125-A200
Bells:
CV48=0 Steel Bell
CV48=64 Bronze Bell
Add values from above for total CV48 value.
Default CV48 Value = 64
0 - EMD 16cyl 567C
0 - Nathan Single Chime
64 - Bronze Bell
Total 0+0+64 = 64
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/ Hide description more…
H0 N XL L M4
- Article numbers
- 73436, 73836, 73336
- Last change
- 9/30/2016
- Manufacturer
- ESU electronic solutions ulm
License Agreement
1. GRANT OF LICENSE
1.1 ESU grants you a non-transferable, limited, non-exclusive right to use the Content solely for your own personal purposes. You may load the Content into RAM, as well as installation on a hard disk or other storage device on a single computer, hardware product or mobile device owned by you or under your control. The installation process may result in a copy of the Content residing on your computer, in which case, you may retain one (1) copy of the Content on your computer, provided that you retain all copyright and other proprietary notices on the copy and the copy is kept in your possession with the original.1.2 By using the Content, you shall not obtain any ownership, copyright, proprietary or other interest in or to the Content. The Content is licensed, not sold.
1.3 You are licensed to use, modify and combine the Sound Samples with sound samples provided by third parties, to create your own sound compositions which, subject to you complying with the terms of this Agreement, you are free to distribute as you wish provided that: (i) the Sound Samples have been mixed together to create an original work; (ii) individual Sound Samples are not used in isolation and (iii) the Sound Samples or derivatives are not used to create sound libraries for distribution to third parties.
2. PROHIBITED USES
Neither you, nor anyone at your direction, shall:2.1 use the Content, or any part of it, for any public performance, live broadcast or time delayed live broadcast where the Content is used unattended for commercial purposes without ESU' s prior written consent;
2.2 use the Content, or any part of it, in any competitive product;
2.3 sub-license, copy, reproduce, transmit, assign, rent, sell, lease, offer on a pay-per-play basis, distribute for money or any other consideration, or commercially exploit in any other manner or through any medium whatsoever or otherwise transfer in any way the Content or any part thereof;
2.4 manufacture and/or distribute for money or otherwise commercially exploit any product that incorporates any part of the Content. If you wish to use any part of the Content for manufacture, resale, sub-license or further distribution, you must contact ESU (and where relevant, its licensors) to enter into an appropriate agreement with ESU (and, where relevant, its licensors);
2.5 publish the results of any analysis or comparative evaluation of the Content or any part thereof without ESU' s prior written consent;
2.6 reverse engineer, recompile or disassemble any part of the Content except to the extent and in the circumstances expressly permitted by ESU and its licensors in writing or by law;
3. INTELLECTUAL PROPERTY RIGHTS
You acknowledge that all intellectual property rights in the Content are and shall remain vested in ESU and its licensors. You undertake not to interfere with or diminish, whether by act or omission, the rights, title and interest in the Content of ESU and its licensors. You may be held responsible by ESU and/or any of its licensors for any infringement of any intellectual property rights in the Content. For the avoidance of doubt, provided that you comply with the terms of this Agreement, ESU shall not claim ownership of the intellectual property rights in any compositions created by your use of the Content.4. TERM AND TERMINATION
This Agreement is effective from the first date you install the Content. The rights granted to you under this Agreement shall terminate if you fail to abide by its terms. Upon such termination you agree to destroy the Content including any Content stored on the hard disk of any computer under your control. You may terminate this Agreement at any time by destroying or erasing all your copies of the Content. Any termination of this Agreement (howsoever occasioned) shall not affect any accrued rights or liabilities of you or ESU nor shall it affect the coming into force or the continuance in force of the provisions of Clauses 2, 3, 5 and 6 and any provision hereof which is by implication intended to come into or continue in force on or after such termination.5. NO WARRANTIES
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ESU AND ITS LICENSORS PROVIDE THE CONTENT "AS IS" AND ESU EXCLUDES ON BEHALF OF ITSELF AND ITS LICENSORS, ALL CONDITIONS, TERMS, REPRESENTATIONS (OTHER THAN FRAUDULENT REPRESENTATIONS) AND WARRANTIES RELATING TO THE CONTENT, WHETHER IMPOSED BY STATUTE OR BY OPERATION OF LAW OR OTHERWISE, INCLUDING BUT NOT LIMITED TO, IMPLIED WARRANTIES OF SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE. NEITHER ESU NOR ITS LICENSORS WARRANT THAT THE OPERATION OF THE CONTENT WILL BE UNINTERRUPTED, ERROR FREE, VIRUS FREE OR MEET YOUR SPECIFIC REQUIREMENTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM JURISDICTION TO JURISDICTION.6. ESU's LIABILITY
Neither ESU nor its licensors shall have any liability to you for any loss or damage caused directly or indirectly in connection with the Content, any part thereof or this Agreement, except to the extent that such liability cannot be lawfully excluded. In any case, neither ESU nor its licensors shall be liable for any loss of business, data, profits, savings, or any other special, incidental, consequential, indirect or economic loss whatsoever even if such losses were contemplated at the date of this Agreement.7. GENERAL
7.1 You acknowledge that damages alone might be insufficient remedy for any breach of the terms of this Agreement and that the remedies of injunction, specific performance or other equitable relief would be suitable remedies in the event of any breach or threatened breach of this Agreement.7.2 You may not assign or otherwise transfer all or any part of this Agreement or the rights granted to you hereunder.
7.3 ESU is not obliged to provide any maintenance, technical support or upgrades to you.
7.4 You agree to comply with all applicable import and export regulations and acknowledge that you have the responsibility for obtaining all necessary licenses to export, re-export, transfer or import the Content.
7.5 This Agreement constitutes the entire agreement between you and ESU with respect to the subject matter hereof and supersedes all prior agreements, arrangements and understandings between the parties and constitutes the entire agreement between the parties relating to such subject matter hereof. No addition to or modification of any provision of this Agreement shall be binding upon ESU and you unless made by a written instrument signed by a duly authorized representative of ESU and you.
7.6 No forbearance, delay or indulgence by either party in enforcing the provisions of this Agreement shall prejudice or restrict the rights of that party nor shall any waiver of its rights operate as a waiver of any subsequent breach and no right, power or remedy herein conferred upon or reserved for either party is exclusive of any other right, power or remedy available to that party and each such right, power or remedy shall be cumulative.
7.7 Notwithstanding that the whole or any part of any provision of this Agreement may prove to be illegal or unenforceable the other provisions of this Agreement and the remainder of the provision in question shall remain in full force and effect.
If you download the designated file, you agree to be legally bound by the license given above.