- Downloads
- Sounds
- projects.esu.eu
- Search results
BLW 6-606A LokSound 5 North American and Australian Sound files 
H0 N XL L M4
- Article numbers:S0789
- Last change: 11/18/2020
- Manufacturer: ESU
Baldwin 606A Prime Movers were used in a few Baldwin prototypes.
RS-12, S-12
Recorded from a BLW S-12
This project is a normal idle version. It is an air throttle version. It has a single exhaust stack.
File also contains an "Isolation Switch" Mode on F15 when Standing Still.
Pressing F15 while not moving will lower the prime mover and lock the motor. F15 must be turned off to begin moving.
Another Mode is "Reverser In Center Position". When pressing F24 while stopped, the motor will lock so you can throttle through the notches like the prototype in neutral. F24 must be turned off to begin moving.
This project has "Run 8" mode. When turning on F26 with F28 off, the prime mover goes to run 8. Turning off F26 returns the prime mover sounds back to normal mode.
This project has "Coast" mode. When turning on F27 with F28 off, the prime mover goes to idle for coasting purposes. Turning off F27 returns the prime mover sounds back to normal mode.
You can still use F26 and F27 for manual nothing. You have to keep both F26 and F27 off before pressing F28 to turn on manual notching. Once F28 is on, you can use F26 to notch up and F27 to notch down. F26, F27, and F28 must be turned off to return to normal mode.
This project has "Load" mode. When turning on F29 with F15, F24, F26, F27, F28 off, the prime mover goes into load mode. While you are using load mode, the prime mover will notch up 1 or more notches based on primary load settings(CV104). The throttle notches up using speed instead of requested speed while using the load feature. F29 must be turned off to return to normal mode.
1st Gen Horn Pack 1
Horns (SoundCV9):
CV163=0 Leslie A-125
CV163=1 Leslie A-200
CV163=2 Leslie S-2M
CV163=3 Leslie S-3K
CV163=4 Leslie S-3L
CV163=5 Leslie S-5T
CV163=6 Nathan M3
CV163=7 Nathan M3H
CV163=8 Nathan M5
CV163=9 Nathan P5 (Old Cast)
CV163=10 Nathan P5R24 (Old Cast)
CV163=11 Nathan P3 (Old Cast)
CV163=12 Nathan P3-R4 (Old Cast)
CV163=13 Nathan P5A (Old Cast)
CV163=14 Wabco E-2
Baldwin Bell Template Pack 1
Bells (SoundCV10):
CV164=0 Baldwin Brass Bell 001
CV164=1 UKM B443 Steel Bell 005
Auto Bell:
Many Second and Third Generation locomotives have been fitted with an Automatic Bell that is triggered when the horn is blown. In MANY cases this cannot even be bypassed on modern locos. Before the FRA mandated this feature on new locomotives the bell was of course turned on and off separately. Some locomotives were delivered with a manual bell and have been converted to an automatic bell. This creates a challenge in sound file creation.
We realize that not every loco with a particular prime mover had this feature. As such we have built in an option to turn the feature on and off. We will set the default in the file to be what is most appropriate for the particular file.
To turn the feature OFF - Auto Bell OFF:
1. Remove the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 4
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 0
To turn the feature ON - Auto Bell ON:
1. ADD the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 12
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 1
Auto Bell Timer:
The Bell timer is amount of time the bell will play after the horn if the auto timer is active. The timer is broken down into 1/4 of a second increments.
CV169=4 - 1 Second
CV169=8 - 2 Seconds
CV169=12 - 3 Seconds
CV169=16 - 4 Seconds
CV169=20 - 5 Seconds - Default
Etc...
Switcher Brake Squeal Template Pack 1
Brake Squeal (SoundCV11)
CV165=0 Composition Shoe #1
CV166=1 Cast Iron Shoe #1
ALCO Air Dryer Template Pack 1
Air Dryer (SoundCV12)
CV166=0 S-1 Air Dryer 1
CV166=1 C-425 Air Dryer 1
CV166=2 RS-18 Air Dryer 1
CV166=3 RS-18 Air Dryer 2 Hide description more…
H0 N XL L M4
- Article numbers
- S0789
- Last change
- 11/18/2020
- Manufacturer
- ESU
#484 CTS BLW 2-8-2 LokSound 5 North American and Australian Sound files H0 N XL L M4
- Article numbers:S0791
- Last change: 4/2/2024
- Manufacturer: ESU
Recorded from Cumbres and Toltec #484
We would like to give a special thanks to the Cubres and Toltec Scenic Railroad for their help in this project. To find out more about their operation or to book a ride please go to: https://cumbrestoltec.com/
The Denver and Rio Grande Western K-36 class are ten 3 ft (914 mm) narrow gauge 2-8-2 "Mikado" type steam locomotives built for the Denver and Rio Grande Western Railroad (D&RGW) by Baldwin Locomotive Works. They were shipped to the Rio Grande in 1925 and were first used along the Monarch Branch and Marshall Pass, but were later sent to the Third Division out of Alamosa. Of the original ten, four are owned by the Durango and Silverton Narrow Gauge Railroad (D&SNG) and five by the Cumbres and Toltec Scenic Railroad (C&TS). Number 485 fell into the turntable pit at Salida and was scrapped in Pueblo in 1955, with many parts being saved.
The locomotives are of outside-frame design, with the driving wheels placed between the two chassis frames which support the boiler, but with the cylinders, driving rods, counterweights and valve gear on the outside. This general arrangement is shared with the earlier K-27, K-28 and later K-37 Mikado engines.
Whistles:
CV163=0 HVSR #3 Crosby 3 Chime"
CV163=1 D&RGW 5 Chime
CV163=2 Soo Line 1003
CV163=3 SP 4449 Daylight
CV163=4 Single Chime Hooter
CV163=5 CN 4 Chime
CV163=6 PRR Banshee #1
CV163=7 D&RGW 484
CV163=8 D&RGW 463
CV163=9 D&RGW 488
Bells:
CV164=0 #3 HVSR Bell 1
CV164=1 Pnuematic Bell 2
CV164=2 Rope Pull Bell
CV164=3 SOO Line 1003 Bell
CV164=4 D&RGW K27 Bell
Brake Squeal:
CV165=0 Brake Squeal #1 Long
CV165=1 Brake Squeal #1 Short
CV165=2 Brake Squeal #2 Long
CV165=3 Brake Squeal #2 Short
CV165=4 Brake Squeal #3 Long
CV165=5 Brake Squeal #4Short
Dynamos:
CV166=0 Soo Line 1003 Dynamo
CV166=1 K27 463 Dynamo
Air Pumps
CV167=0 Cross Compound #1 Soo Line 1003
CV167=1 Cross Compound #2 K27 463
CV167=1 Cross Compound #3 SP 4449
CV167=1 Cross Compound #4 UP 844
CV167=2 Single Stage #1 Z27
CV167=3 D&RGW #484 Pump
Reversers
CV168=0 Johnson Bar
CV168=1 Power Reverse
The ESU Full Throttle Steam files now include a few new logic features for added operational realism while still leaving you in control of HOW YOU wish to run your locomotive.
Heavy Load: F9 by default.
Similar to the “Drive Hold” button on the Full Throttle Diesel files “Heavy Load” allows you to adjust the “Steam Cut Off Valve” at any speed allowing for a fierce full chuff or drifting with snifters and rod clanks. Heavy load can also act as an offset allowing speed adjustments when engaged if desired.
Coast: F4 by default.
Opposite of “Heavy Load” Coast allows for a negative offset allow drifting sounds of Rods and snifter valves at any speed. You again have the option to hold the speed to adjust the speed with this offset active. Even allowing for an increase of speed with no chuffs as if drifting downhill.
Independent brake: F10 by default
Identical to the Full Throttle Diesel files. This allows for the locomotive to stop more quickly than its regular momentum would normally carry it. This one is pretty self-explanatory – just press the brake and come to a stop! For additional options there are 3 Braking rates that can be set up for user preference.
Articulation: Sound Slot 2
By adding Sound Slot 2 to the F8 Function Mapping and enabling the "Secondary Trigger" (CV250) you can add a second set of drivers making any ESU Steam File articulated.
Function Mappable Air Horn: F21 by default
Sound Slot 21.
Many Steam locomotives had a single chime airhorn equipped. Those modelling SP, MILW, and others can now have this feature and put it where they would like in the function mapping in addition to the whistle.
S0791 - Release Notes
===================================================
V-4 R-3:
===================================================
- updated independent brake
- updated boiler hiss
- updated steam chuff sound slot
V-5 R-4:
===================================================
- changed whistle sound slot 3 maximum sound slot speed to 128 Hide description more…
H0 N XL L M4
- Article numbers
- S0791
- Last change
- 4/2/2024
- Manufacturer
- ESU
#110 BHCR BLW 2-6-6-2T LokSound 5 North American and Australian Sound files H0 N XL L M4
- Article numbers:S0793
- Last change: 4/2/2024
- Manufacturer: ESU
Recorded from Black Hills Central Rrailroad #110
We would like to give a special thanks to the BHCR for their help in this project. To find out more about their operation or to book a ride please go to: https://www.1880train.com/
This is a 2-6-6-2T articulated Mallet that was built by The Baldwin Locomotive Works in 1928 for the Weyerhaeuser Timber Company of Vail, WA. Its next stop was The Rayonier Lumber Company where it received a tender from Rayonier #101 and was retired in 1968. This engine was later displayed at the Wasatch Mountain Railway in Heber City, UT, and then sold to the Nevada State Railway Museum. The #110 was sold to The BHC in 1999 and was trucked from Nevada to South Dakota on four semi-trailers. Restoration on this engine was completed in the spring of 2001.
True Mallet Locomotives are compound locomotives utilizing the steam multiple times. Because the exhaust from the first cylinders (high pressure) gets reused by the next set of cylinders (low pressure) the "double chuff" often associated with articulated locomotives is not really present.
While recorded from a 2-6-6-2T this file can be used for simiar Mallet type locomotives.
Whistles:
CV163=0 BHCR #110 CB&Q 5 Chime *
CV163=1 DRG&W 5-Chime
CV163=2 Soo #1003
CV163=3 SP #4449
CV163=4 UP #844*
CV163=5 WM 3-Chime *
CV163=6 WM 6-Chime
CV163=7 SP&S 3-Chime *
CV163=8 DL&W #261 5-Chime
Bells:
CV164=0 BHCR #110 Bell *
CV164=1 Pnuematic Bell 2
CV164=2 Rope Pull Bell
CV164=3 SOO Line 1003 Bell
CV164=4 DRG&W K27 Bell
Brake Squeal:
CV165=0 Brake Squeal #1 Long
CV165=1 Brake Squeal #1 Short
CV165=2 Brake Squeal #2 Long
CV165=3 Brake Squeal #2 Short
CV165=4 Brake Squeal #3 Long
CV165=5 Brake Squeal #4Short
Dynamos:
CV166=0 Soo Line 1003 Dynamo
CV166=1 K27 463 Dynamo
CV166=2 T16.1 Dynamo
Air Pumps
CV167=0 Cross Compound #1 Soo Line 1003
CV167=1 Cross Compound #2 K27 463
CV167=2 Single Stage #1 Z27
CV167=3 Single Stage slow Air Pump #1 Z27
CV167=4 BHCR Slow Air Pump *
The ESU Full Throttle Steam files now include a few new logic features for added operational realism while still leaving you in control of HOW YOU wish to run your locomotive.
Heavy Load: F9 by default.
Similar to the “Drive Hold” button on the Full Throttle Diesel files “Heavy Load” allows you to adjust the “Steam Cut Off Valve” at any speed allowing for a fierce full chuff or drifting with snifters and rod clanks. Heavy load can also act as an offset allowing speed adjustments when engaged if desired.
Coast: F4 by default.
Opposite of “Heavy Load” Coast allows for a negative offset allow drifting sounds of Rods and snifter valves at any speed. You again have the option to hold the speed to adjust the speed with this offset active. Even allowing for an increase of speed with no chuffs as if drifting downhill.
Independent brake: F10 by default
Identical to the Full Throttle Diesel files. This allows for the locomotive to stop more quickly than its regular momentum would normally carry it. This one is pretty self-explanatory – just press the brake and come to a stop! For additional options there are 3 Braking rates that can be set up for user preference.
Articulation: Sound Slot 2
By adding Sound Slot 2 to the F8 Function Mapping and enabling the "Secondary Trigger" (CV250) you can add a second set of drivers making any ESU Steam File articulated.
Function Mappable Air Horn: F21 by default
Sound Slot 21.
Many Steam locomotives had a single chime airhorn equipped. Those modelling SP, MILW, and others can now have this feature and put it where they would like in the function mapping in addition to the whistle.
S0793 - Release Notes
===================================================
V-4 R-3:
===================================================
- updated independent brake
- updated boiler hiss
- updated steam chuff sound slot
V-5 R-4:
===================================================
- changed whistle sound slot 3 maximum sound slot speed to 128 Hide description more…
H0 N XL L M4
- Article numbers
- S0793
- Last change
- 4/2/2024
- Manufacturer
- ESU
#40 NN BLW 4-6-0 LokSound 5 North American and Australian Sound files H0 N XL L M4
- Article numbers:S0795
- Last change: 4/2/2024
- Manufacturer: ESU
Recorded from Nevada Northern Railway #40.
We would like to give a special thanks to the NNRY for their help in this project. To find out more about their operation or to book a ride please go to: https://nnry.com/
The Nevada Northern No. 40 is a 4-6-0 ten-wheeler type, steam locomotive which was built by the Baldwin Locomotive Works of Philadelphia, Pennsylvania in July 1910 for the Nevada Northern Railway Company.
It originally served as a passenger locomotive during the original years of when the Nevada Northern was a US Class 2 railroad as the main locomotive for the railroad's crack passenger train, the "Steptoe Valley Flyer". Before the Nevada Northern retired the locomotive in 1941, the locomotive was given a complete overhaul in secret by the shop crews in the Ely roundhouse. The locomotive was then put onto standby service. Afterwards, it was used in 1956 for the railroad's 50th Anniversary excursion and pulling a charter train for the Central Coast Railway Club in 1958 before being tucked back into retirement in the very back of the Ely roundhouse, preserved along with several passenger cars that were used with the locomotive since then. This was the last time the locomotive operated in revenue service. When the Nevada Northern shut down in the 1980's, the City of Ely was given the historic locomotive and train, along with the entire East Ely Yard, which was unaltered since being built in 1906, and any of the equipment and all of it which was inside the donated property. It is now currently used as a mixed traffic unit with the other Nevada Northern steam and diesel locomotives. But, its most famous role is the main locomotive for the "Ghost Train of Old Ely" excursion train.
Nevada Northern #40 ran it’s final excursion run on October 19th 2020, and it is now undergoing a complete rebuild.
Whistles:
CV163=0 B&O 3-Chime
CV163=1 HVSR #3 Crosby 3-Chime
CV163=2 L&N Passenger
CV163=3 NN #40
CV163=4 NYC 6-Chime
CV163=5 RDG 6-Chime
CV163=6 Southern Bootleg Hooter
CV163=7 SP&S 3-Chime
Bells:
CV164=0 #40 NN Bell
CV164=1 Pnuematic Bell 2
CV164=2 Rope Pull Bell
CV164=3 SOO Line 1003 Bell
CV164=4 DRG&W K27 Bell
Brake Squeal:
CV165=0 Brake Squeal #1 Long
CV165=1 Brake Squeal #1 Short
CV165=2 Brake Squeal #2 Long
CV165=3 Brake Squeal #2 Short
CV165=4 Brake Squeal #3 Long
CV165=5 Brake Squeal #4Short
Dynamos:
CV166=0 Soo Line 1003 Dynamo
CV166=1 K27 463 Dynamo
CV166=2 T16.1 Dynamo
Air Pumps
CV167=0 Cross Compound #1 Soo Line 1003
CV167=1 Cross Compound #2 K27 463
CV167=2 Single Stage #1 Z27
CV167=3 Air Pump NN #40
Reversers
CV168=0 Johnson Bar
CV168=1 Power Reverse
The ESU Full Throttle Steam files now include a few new logic features for added operational realism while still leaving you in control of HOW YOU wish to run your locomotive.
Heavy Load: F9 by default.
Similar to the “Drive Hold” button on the Full Throttle Diesel files “Heavy Load” allows you to adjust the “Steam Cut Off Valve” at any speed allowing for a fierce full chuff or drifting with snifters and rod clanks. Heavy load can also act as an offset allowing speed adjustments when engaged if desired.
Coast: F4 by default.
Opposite of “Heavy Load” Coast allows for a negative offset allow drifting sounds of Rods and snifter valves at any speed. You again have the option to hold the speed to adjust the speed with this offset active. Even allowing for an increase of speed with no chuffs as if drifting downhill.
Independent brake: F10 by default
Identical to the Full Throttle Diesel files. This allows for the locomotive to stop more quickly than its regular momentum would normally carry it. This one is pretty self-explanatory – just press the brake and come to a stop! For additional options there are 3 Braking rates that can be set up for user preference.
Articulation: Sound Slot 2
By adding Sound Slot 2 to the F8 Function Mapping and enabling the "Secondary Trigger" (CV250) you can add a second set of drivers making any ESU Steam File articulated.
Function Mappable Air Horn: F21 by default
Sound Slot 21.
Many Steam locomotives had a single chime airhorn equipped. Those modelling SP, MILW, and others can now have this feature and put it where they would like in the function mapping in addition to the whistle.
S0795 - Release Notes
===================================================
V-3 R-3:
===================================================
- updated independent brake
- updated boiler hiss
- updated steam chuff sound slot
V-4 R-4:
===================================================
- changed whistle sound slot 3 maximum sound slot speed to 128 Hide description more…
H0 N XL L M4
- Article numbers
- S0795
- Last change
- 4/2/2024
- Manufacturer
- ESU
#90 SCR BLW 2-10-0 LokSound 5 North American and Australian Sound files H0 N XL L M4
- Article numbers:S0799
- Last change: 4/29/2024
- Manufacturer: ESU
Strasburg Rail Road (Great Western) No. 90 is a 2-10-0 "Decapod" type steam locomotive owned and operated by the Strasburg Rail Road outside of Strasburg, Pennsylvania. Built by the Baldwin Locomotive Works in 1924, No. 90 originally pulled sugar beet trains for the Great Western Railway of Colorado. In 1967, No. 90 was sold to the Strasburg Rail Road where it now resides and operates today for use on excursion trains. As of today, No. 90 is one of only two operational Decapod type steam locomotives in America, the other being Frisco No. 1630 at the Illinois Railway Museum in Union, Illinois.
The locomotive was built by the Baldwin Locomotive Works in June 1924, in Philadelphia. it originally pulled sugar beet trains of about 40 to 50 cars length for the Great Western Railway of Colorado to the company's towering mill in Loveland, Colorado. It was the Great Western's largest and most powerful road locomotive, and saw extensive use on trains too large for the company's fleet of 2-8-0s. On November 7, 1944, the engine was hit by a truck at a grade crossing east of Loveland and knocked onto its fireman's side, killing both the fireman and the truck driver. The Great Western sent 90 to the Chicago, Burlington and Quincy Railroad's shops in Denver for repairs. Following WWII, the locomotive was used primarily in the Autumn during the harvest season.
By the late 1950s, the engine was occasionally used in excursion service on the Great Western. In 1963, No. 90 pulled a few special excursions for that year's National Railway Historical Society Convention, were it was held in Denver at the time. On one such excursion, Strasburg Rail Road's Chief Mechanical Officer, Huber Leath, met the Great Western's superintendent, a man who grew up in the vicinity of the Strasburg Rail Road and struck a deal in which the Great Western would contact the Strasburg Rail Road as soon as the engine was available for purchase. The Strasburg Rail Road purchased No. 90 on April 5, 1967, for a price of $23,000.00(~$175,000 in 2019) and the locomotive arrived on Strasburg's property a month later on May 5, 1967.
In the winter of 1968, Ross Rowland's High Iron Company planned to operate a series of mainline steam excursions between Jersey City, New Jersey and Wilkes-Barre, Pennsylvania on the Central Railroad of New Jersey. Rowland had originally planned to lease two ex Canadian Pacific G5-class 4-6-2s, numbers 1238 and 1286, both owned by George M. Hart. However, those two locomotives were on emergency leases to the city of Reading, Pennsylvania to provide steam for the city after the boiler at the Reading Steam Heat and Power Co. became disabled. Since tickets for the excursion had already been sold, and Rowland was unwilling to pull the trip with a diesel, he leased Steamtown's ex Canadian Pacific 127 (formerly 1278), a sister to the two locomotives he intended to use to pull the train. However, the 127 did not have enough power to pull the train over the grades on the CNJ near Jim Thorpe, Pennsylvania on her own and Rowland leased the 90 to act as a helper engine for the trips, double-heading with the 127 between Bethlehem and Jim Thorpe, Pennsylvania. After the trips concluded, No. 90 was returned to Strasburg.
As it was on the Great Western, the engine is also the most powerful of the four steam locomotives in operation at the Strasburg Rail Road in Lancaster County, Pennsylvania, rated for 1,211 tons on the line. It is currently one of the only two 2-10-0 Decapods operating in the United States, the other one is former Frisco No. 1630, which operates at the Illinois Railway Museum.
No. 90 has had numerous modifications during its time at Strasburg, the most recent being in 2013, in which it was repainted in a new paint scheme similar to what it originally wore back in the 1990s. Differences include the yellow pin striping and lettering, which is currently painted / stenciled in white. Its smokebox was painted silver, and its number plate was black. In 2015, No. 90 went through another modification, where its smokebox color changed from silver to brown. After this modification, 90 was to return to service in February 2016. As of January 2023, No. 90 is still operational, but in early 2024, it is currently undergo its Federal Railroad Administration (FRA) federally mandated 1,472-day boiler inspection and overhaul.
Whistles:
CV163=0 SCR #90
CV163=1 SP&S 3-Chime
CV163=2 PRR 3-Chime
CV163=3 NKP #765
CV163=4 MILW #261
CV163=5 Hooter
CV163=6 Hancock Long Bell 3-Chime
CV163=7 DRGW #346
Bells:
CV164=0 #90 SCR Bell 1
CV164=1 Pnuematic Bell 2
CV164=2 Rope Pull Bell
CV164=3 SOO Line 1003 Bell
Brake Squeal:
CV165=0 Brake Squeal #1 Long
CV165=1 Brake Squeal #1 Short
CV165=2 Brake Squeal #2 Long
CV165=3 Brake Squeal #2 Short
CV165=4 Brake Squeal #3 Long
CV165=5 Brake Squeal #4Short
Dynamos:
CV166=0 SCR #90 Dynamo
CV166=1 K27 463 Dynamo
Air Pumps
CV167=0 Cross Compound #1 Soo Line 1003
CV167=1 Cross Compound #2 K27 463
CV167=2 Single Stage #1 Z27
CV167=3 SCR #90
Reversers
CV168=0 Johnson Bar
CV168=1 Power Reverse
The ESU Full Throttle Steam files now include a few new logic features for added operational realism while still leaving you in control of HOW YOU wish to run your locomotive.
Heavy Load: F9 by default.
Similar to the “Drive Hold” button on the Full Throttle Diesel files “Heavy Load” allows you to adjust the “Steam Cut Off Valve” at any speed allowing for a fierce full chuff or drifting with snifters and rod clanks. Heavy load can also act as an offset allowing speed adjustments when engaged if desired.
Coast: F4 by default.
Opposite of “Heavy Load” Coast allows for a negative offset allow drifting sounds of Rods and snifter valves at any speed. You again have the option to hold the speed to adjust the speed with this offset active. Even allowing for an increase of speed with no chuffs as if drifting downhill.
Independent brake: F10 by default
Identical to the Full Throttle Diesel files. This allows for the locomotive to stop more quickly than its regular momentum would normally carry it. This one is pretty self-explanatory – just press the brake and come to a stop! For additional options there are 3 Braking rates that can be set up for user preference.
Articulation: Sound Slot 2
By adding Sound Slot 2 to the F8 Function Mapping and enabling the "Secondary Trigger" (CV250) you can add a second set of drivers making any ESU Steam File articulated.
Function Mappable Air Horn: F21 by default
Sound Slot 21.
Many Steam locomotives had a single chime airhorn equipped. Those modelling SP, MILW, and others can now have this feature and put it where they would like in the function mapping in addition to the whistle.
S0799 - Release Notes
===================================================
V-1 R-1:
===================================================
- new project Hide description more…
H0 N XL L M4
- Article numbers
- S0799
- Last change
- 4/29/2024
- Manufacturer
- ESU
#25 V&T BLW 4-6-0 LokSound 5 North American and Australian Sound files H0 N XL L M4
- Article numbers:S0802
- Last change: 4/2/2024
- Manufacturer: ESU
Recorded from Virginia & Truckee #25
We would like to give a special thanks to the Nevada State Railroad Museum for their help in this project. To find out more about their operation or to book a ride please go to: https://www.hvsry.org/
Virginia & Truckee #25 was built in 1905 by the Baldwin Locomotive Works of Philidelphia, Pennsylvania.
This was the second #25 owned by the V&T. The 4-6-0 steam locomotive, became the first new locomotive the V&T ordered since 1876.
The V&T #25 was originally a coal burner, but in 1907 it was converted into an oil burner, and became a also back-up locomotive. On occasions, the locomotive would haul both freight and passenger trains between Reno, Virginia City, and Carson, when the need for the engine to be used for back-up arised. From 1911 and 1937, the locomotive operated over 80,000 miles during it's service on the V&T. In 1938, V&T #25 was the locomotive that pulled the last scheduled passenger train to Virginia City.
While recorded from an early 1905 4-6-0 this file can be used for smaller locomotives in many wheel arrangments.
Whistles:
CV163=0 V&T #25
CV163=1 #3 HVSR Crosby 3 Chime
CV163=2 NN #40
CV163=3 Robert Swanson 6-Chime
CV163=4 SCR #90
CV163=5 V&T #29
Bells:
CV164=0 #25 V&T Bell
CV164=1 Pnuematic Bell 2
CV164=2 Rope Pull Bell
CV164=3 SOO Line 1003 Bell
CV164=4 DRG&W K27 Bell
Brake Squeal:
CV165=0 Brake Squeal #1 Long
CV165=1 Brake Squeal #1 Short
CV165=2 Brake Squeal #2 Long
CV165=3 Brake Squeal #2 Short
CV165=4 Brake Squeal #3 Long
CV165=5 Brake Squeal #4Short
Dynamos:
CV166=0 Soo Line 1003 Dynamo
CV166=1 K27 463 Dynamo
CV166=2 T16.1 Dynamo
Air Pumps
CV167=0 Cross Compound #1 Soo Line 1003
CV167=1 Cross Compound #2 K27 463
CV167=2 Single Stage #1 Z27
CV167=3 Air Pump V&T #25
Reversers
CV168=0 Johnson Bar
CV168=1 Power Reverse
The ESU Full Throttle Steam files now include a few new logic features for added operational realism while still leaving you in control of HOW YOU wish to run your locomotive.
Heavy Load: F9 by default.
Similar to the “Drive Hold” button on the Full Throttle Diesel files “Heavy Load” allows you to adjust the “Steam Cut Off Valve” at any speed allowing for a fierce full chuff or drifting with snifters and rod clanks. Heavy load can also act as an offset allowing speed adjustments when engaged if desired.
Coast: F4 by default.
Opposite of “Heavy Load” Coast allows for a negative offset allow drifting sounds of Rods and snifter valves at any speed. You again have the option to hold the speed to adjust the speed with this offset active. Even allowing for an increase of speed with no chuffs as if drifting downhill.
Independent brake: F10 by default
Identical to the Full Throttle Diesel files. This allows for the locomotive to stop more quickly than its regular momentum would normally carry it. This one is pretty self-explanatory – just press the brake and come to a stop! For additional options there are 3 Braking rates that can be set up for user preference.
Articulation: Sound Slot 2
By adding Sound Slot 2 to the F8 Function Mapping and enabling the "Secondary Trigger" (CV250) you can add a second set of drivers making any ESU Steam File articulated.
Function Mappable Air Horn: F21 by default
Sound Slot 21.
Many Steam locomotives had a single chime airhorn equipped. Those modelling SP, MILW, and others can now have this feature and put it where they would like in the function mapping in addition to the whistle.
S0802 - Release Notes
===================================================
V-5 R-5:
===================================================
- updated independent brake
- updated boiler hiss
- updated steam chuff sound slot
V-6 R-6:
===================================================
- changed whistle sound slot 3 maximum sound slot speed to 128 Hide description more…
H0 N XL L M4
- Article numbers
- S0802
- Last change
- 4/2/2024
- Manufacturer
- ESU
#425 RBMN BLW 4-6-2 LokSound 5 North American and Australian Sound files H0 N XL L M4
- Article numbers:S0804
- Last change: 4/2/2024
- Manufacturer: ESU
Recorded from Reading Northern #425
We would like to give a special thanks to the Reading and Northern Railroad for their help in this project.
Reading Blue Mountain & Northern Railroad 425 is a 4-6-2 light "Pacific" type steam locomotive originally built in 1928 by the Baldwin Locomotive Works for the Gulf, Mobile & Northern Railroad. After the GM&N was consolidated into the Gulf, Mobile & Ohio Railroad in 1940, the locomotive was renumbered #580 and served in passenger service before being retired in 1950. Today, the locomotive is owned and operated by the Reading & Northern Railroad, based out of Port Clinton, Pennsylvania in excursion service.
While recorded from a light pacific 4-6-2 this file can be used for smaller locomotives in many wheel arrangments.
Whistles:
CV163=0 HVSR #3 Crosby 3 Chime *
CV163=1 #425 RBMN *
CV163=2 Soo Line 1003
CV163=3 SP 4449 Daylight
CV163=4 Single Chime Hooter
CV163=5 CPR 2317
CV163=6 Western Maryland 6 Chime
CV163=7 CN 4 Chime
CV163=8 PRR Banshee #1
CV163=9 DRG&W 484
CV163=10 PRR Pre-War 3-Chime *
CV163=11 RDG 6-Chime *
Bells:
CV164=0 #3 HVSR Bell 1
CV164=1 Pnuematic Bell 2
CV164=2 #425 RBMN Bell
CV164=3 SOO Line 1003 Bell
CV164=4 DRG&W K27 Bell
Brake Squeal:
CV165=0 Brake Squeal #1 Long
CV165=1 Brake Squeal #1 Short
CV165=2 Brake Squeal #2 Long
CV165=3 Brake Squeal #2 Short
CV165=4 Brake Squeal #3 Long
CV165=5 Brake Squeal #4Short
Dynamos:
CV166=0 Soo Line 1003 Dynamo
CV166=1 K27 463 Dynamo
Air Pumps
CV167=0 Cross Compound #1 Soo Line 1003
CV167=1 Cross Compound #2 K27 463
CV167=2 #425 RBMN Air Pump
CV167=3 Westinghouse Single Stage 9" Air Pump HVSR #3
Reversers
CV168=0 Johnson Bar
CV168=1 Power Reverse
The ESU Full Throttle Steam files now include a few new logic features for added operational realism while still leaving you in control of HOW YOU wish to run your locomotive.
Heavy Load: F9 by default.
Similar to the “Drive Hold” button on the Full Throttle Diesel files “Heavy Load” allows you to adjust the “Steam Cut Off Valve” at any speed allowing for a fierce full chuff or drifting with snifters and rod clanks. Heavy load can also act as an offset allowing speed adjustments when engaged if desired.
Coast: F4 by default.
Opposite of “Heavy Load” Coast allows for a negative offset allow drifting sounds of Rods and snifter valves at any speed. You again have the option to hold the speed to adjust the speed with this offset active. Even allowing for an increase of speed with no chuffs as if drifting downhill.
Independent brake: F10 by default
Identical to the Full Throttle Diesel files. This allows for the locomotive to stop more quickly than its regular momentum would normally carry it. This one is pretty self-explanatory – just press the brake and come to a stop! For additional options there are 3 Braking rates that can be set up for user preference.
Articulation: Sound Slot 2
By adding Sound Slot 2 to the F8 Function Mapping and enabling the "Secondary Trigger" (CV250) you can add a second set of drivers making any ESU Steam File articulated.
Function Mappable Air Horn: F21 by default
Sound Slot 21.
Many Steam locomotives had a single chime airhorn equipped. Those modelling SP, MILW, and others can now have this feature and put it where they would like in the function mapping in addition to the whistle.
S0804 - Release Notes
===================================================
V-4 R-3:
===================================================
- updated independent brake
- updated boiler hiss
- updated steam chuff sound slot
V-5 R-4:
===================================================
- changed whistle sound slot 3 maximum sound slot speed to 128 Hide description more…
H0 N XL L M4
- Article numbers
- S0804
- Last change
- 4/2/2024
- Manufacturer
- ESU
#1702 GSMR BLW 2-8-0 LokSound 5 North American and Australian Sound files H0 N XL L M4
- Article numbers:S0814
- Last change: 4/2/2024
- Manufacturer: ESU
Recorded from Great Smoky Mountains Railroad #1702.
We would like to give a special thanks to the GSMR for their help in this project. To find out more about their operation or to book a ride please go to: https://www.gsmr.com/steam/
The Great Smoky Mountains Railroad #1702 is a 2-8-0 steam locomotive, built in September 1942 by the Baldwin Locomotive Works in Eddystone, PA. Originally destined to be US Army Transportation Corp #1702, part of their S160 class of 2-8-0 Consolidations, which were also built by Lima & ALCO between 1942 and 1945.
Whistles:
CV163=0 GSMR #1702
CV163=1 DRGW 5-Chime
CV163=2 SOO #1003
CV163=3 SP #4449
CV163=4 Hooter
CV163=5 CPR #2317
CV163=6 WM 6-Chime
CV163=7 CN 4 Chime
CV163=8 PRR Flat Top Single-Chime Banshee
CV163=9 DRGW #484
Bells:
CV164=0 GSMR #1702
CV164=1 Pnuematic Bell 2
CV164=2 Rope Pull Bell
CV164=3 SOO Line 1003 Bell
CV164=4 DRG&W K27 Bell
Brake Squeal:
CV165=0 Brake Squeal #1 Long
CV165=1 Brake Squeal #1 Short
CV165=2 Brake Squeal #2 Long
CV165=3 Brake Squeal #2 Short
CV165=4 Brake Squeal #3 Long
CV165=5 Brake Squeal #4Short
Dynamos:
CV166=0 Soo Line 1003 Dynamo
CV166=1 K27 463 Dynamo
CV166=2 T16.1 Dynamo
Air Pumps
CV167=0 Cross Compound #1 Soo Line 1003
CV167=1 Cross Compound #2 K27 463
CV167=2 Single Stage #1 Z27
CV167=3 Air Pump GSMR #1702
Reversers
CV168=0 Johnson Bar
CV168=1 Power Reverse
The ESU Full Throttle Steam files now include a few new logic features for added operational realism while still leaving you in control of HOW YOU wish to run your locomotive.
Heavy Load: F9 by default.
Similar to the “Drive Hold” button on the Full Throttle Diesel files “Heavy Load” allows you to adjust the “Steam Cut Off Valve” at any speed allowing for a fierce full chuff or drifting with snifters and rod clanks. Heavy load can also act as an offset allowing speed adjustments when engaged if desired.
Coast: F4 by default.
Opposite of “Heavy Load” Coast allows for a negative offset allow drifting sounds of Rods and snifter valves at any speed. You again have the option to hold the speed to adjust the speed with this offset active. Even allowing for an increase of speed with no chuffs as if drifting downhill.
Independent brake: F10 by default
Identical to the Full Throttle Diesel files. This allows for the locomotive to stop more quickly than its regular momentum would normally carry it. This one is pretty self-explanatory – just press the brake and come to a stop! For additional options there are 3 Braking rates that can be set up for user preference.
Articulation: Sound Slot 2
By adding Sound Slot 2 to the F8 Function Mapping and enabling the "Secondary Trigger" (CV250) you can add a second set of drivers making any ESU Steam File articulated.
Function Mappable Air Horn: F21 by default
Sound Slot 21.
Many Steam locomotives had a single chime airhorn equipped. Those modelling SP, MILW, and others can now have this feature and put it where they would like in the function mapping in addition to the whistle.
S0814 - Release Notes
===================================================
V-3 R-3:
===================================================
- updated independent brake
- updated boiler hiss
- updated steam chuff sound slot
V-4 R-4:
===================================================
- changed whistle sound slot 3 maximum sound slot speed to 128 Hide description more…
H0 N XL L M4
- Article numbers
- S0814
- Last change
- 4/2/2024
- Manufacturer
- ESU
#108 BHCR BLW 2-6-6-2T LokSound 5 North American and Australian Sound files H0 N XL L M4
- Article numbers:S0816
- Last change: 4/2/2024
- Manufacturer: ESU
Recorded from Black Hills Central Rrailroad #108
We would like to give a special thanks to the BHCR for their help in this project. To find out more about their operation or to book a ride please go to: https://www.1880train.com/
This is a 2-6-6-2T articulated Mallet that was built by The Baldwin Locomotive Works in 1926.
Pacific Northwest steam historian Martin Hansen offers this perspective: “This 1926 Baldwin 2-6-6-2T spent her entire working career in logging service in the Pacific Northwest. Originally ordered as a coal burner for the Potlach Lumber Co. of Potlach, Idaho where she was No. 24, she later converted to burn oil when she was purchased by Weyerhaeuser Timber Co. for use on that company’s Headquarters Operation out of Longview, Wash., where she became No. 108. She was one of only three Baldwin logging Mallets to be built with full saddle tanks over her boiler, rather than the more common split side tanks found on other tank Mallets of the day.”
The restoration on 108 was completed in 2020 and ran together with the ,110 another 2-6-6-2T, on the Blck Hills Central Railroads first double header.
True Mallet Locomotives are compound locomotives utilizing the steam multiple times. Because the exhaust from the first cylinders (high pressure) gets reused by the next set of cylinders (low pressure) the "double chuff" often associated with articulated locomotives is not really present. They are heard in the more common "simple" type articulated locomotives which are easier to mantain.
While recorded from a 2-6-6-2T this file can be used for simiar Compound Mallet type locomotives.
Whistles:
CV163=0 CB&Q 5 Chime *
CV163=1 DRG&W 5-Chime
CV163=2 Soo #1003
CV163=3 SP #4449
CV163=4 UP #844*
CV163=5 WM 3-Chime *
CV163=6 WM 6-Chime
CV163=7 SP&S 3-Chime *
CV163=8 DL&W #261 5-Chime
Bells:
CV164=0 BHCR #108 Bell *
CV164=1 Pnuematic Bell 2
CV164=2 Rope Pull Bell
CV164=3 SOO Line 1003 Bell
CV164=4 DRG&W K27 Bell
Brake Squeal:
CV165=0 Brake Squeal #1 Long
CV165=1 Brake Squeal #1 Short
CV165=2 Brake Squeal #2 Long
CV165=3 Brake Squeal #2 Short
CV165=4 Brake Squeal #3 Long
CV165=5 Brake Squeal #4Short
Dynamos:
CV166=0 Soo Line 1003 Dynamo
CV166=1 K27 463 Dynamo
CV166=2 T16.1 Dynamo
Air Pumps
CV167=0 Cross Compound #1 Soo Line 1003
CV167=1 Cross Compound #2 K27 463
CV167=2 Single Stage #1 Z27
CV167=3 Single Stage slow Air Pump #1 Z27
CV167=4 BHCR Slow Air Pump *
Reversers
CV168=0 Johnson Bar
CV168=1 Power Reverse
The ESU Full Throttle Steam files now include a few new logic features for added operational realism while still leaving you in control of HOW YOU wish to run your locomotive.
Heavy Load: F9 by default.
Similar to the “Drive Hold” button on the Full Throttle Diesel files “Heavy Load” allows you to adjust the “Steam Cut Off Valve” at any speed allowing for a fierce full chuff or drifting with snifters and rod clanks. Heavy load can also act as an offset allowing speed adjustments when engaged if desired.
Coast: F4 by default.
Opposite of “Heavy Load” Coast allows for a negative offset allow drifting sounds of Rods and snifter valves at any speed. You again have the option to hold the speed to adjust the speed with this offset active. Even allowing for an increase of speed with no chuffs as if drifting downhill.
Independent brake: F10 by default
Identical to the Full Throttle Diesel files. This allows for the locomotive to stop more quickly than its regular momentum would normally carry it. This one is pretty self-explanatory – just press the brake and come to a stop! For additional options there are 3 Braking rates that can be set up for user preference.
Articulation: Sound Slot 2
By adding Sound Slot 2 to the F8 Function Mapping and enabling the "Secondary Trigger" (CV250) you can add a second set of drivers making any ESU Steam File articulated.
Function Mappable Air Horn: F21 by default
Sound Slot 21.
Many Steam locomotives had a single chime airhorn equipped. Those modelling SP, MILW, and others can now have this feature and put it where they would like in the function mapping in addition to the whistle.
S0816 - Release Notes
===================================================
V-4 R-4:
===================================================
- updated independent brake
- updated boiler hiss
- updated steam chuff sound slot
V-5 R-5:
===================================================
- changed whistle sound slot 3 maximum sound slot speed to 128 Hide description more…
H0 N XL L M4
- Article numbers
- S0816
- Last change
- 4/2/2024
- Manufacturer
- ESU
ALCO 6-539T Ed2 LokSound 5 North American and Australian Sound files H0 N XL L M4
- Article numbers:S0825
- Last change: 8/27/2021
- Manufacturer: ESU
The ALCO 539 engine was developed in response to the perceived drawback that ALCO's line of diesel switchers had a restricted field of vision because of the high hood. Both Baldwin and EMC were offering diesel switchers with a lower engine hood that the trainmen could see over.
The 539T was equipped with the Buchi turbocharger, being made under license by the Elliott Manufacturing Company of Jeannette, Pennsylvania. The first 539T engines were used in S-2 switchers and DL-105 passenger locomotives built in September 1940.
ALCO Locomotives:
S-2, S-4, RS-1, RSC-1, RSD-1, DL-105, DL-107, DL-108, DL-109, DL-110
MLW Locomotives:
S-2, S-4, S-7, S-12, RS-1, RSC-13
Recorded from a ALCO RS-1
This project is a normal idle version. It is an air throttle version. It has a single exhaust stack.
File also contains an "Isolation Switch" Mode on F15 when Standing Still.
Pressing F15 while not moving will lower the prime mover and lock the motor. F15 must be turned off to begin moving.
Another Mode is "Reverser In Center Position". When pressing F24 while stopped, the motor will lock so you can throttle through the notches like the prototype in neutral. F24 must be turned off to begin moving.
This project has "Run 8" mode. When turning on F26 with F28 off, the prime mover goes to run 8. Turning off F26 returns the prime mover sounds back to normal mode.
This project has "Coast" mode. When turning on F27 with F28 off, the prime mover goes to idle for coasting purposes. Turning off F27 returns the prime mover sounds back to normal mode.
You can still use F26 and F27 for manual nothing. You have to keep both F26 and F27 off before pressing F28 to turn on manual notching. Once F28 is on, you can use F26 to notch up and F27 to notch down. F26, F27, and F28 must be turned off to return to normal mode.
This project has "Load" mode. When turning on F29 with F15, F24, F26, F27, F28 off, the prime mover goes into load mode. While you are using load mode, the prime mover will notch up 1 or more notches based on primary load settings(CV104). The throttle notches up using speed instead of requested speed while using the load feature. F29 must be turned off to return to normal mode.
1st Generation Switcher Horn Pack 1
Horns (SoundCV9):
CV163=0 Handcock 4700 Whistle
CV163=1 Leslie A-125
CV163=2 Leslie A-200
CV163=3 Leslie S-25
CV163=4 Leslie S-2M
CV163=5 Leslie S-3K
CV163=6 Leslie S-3L
CV163=7 Nathan M-3
CV163=8 Nathan M-5
CV163=9 Nathan P-2 (Temp Nathan P-3-OC)
CV163=10 Nathan P-3-OC
CV163=11 Nathan P-5-OC
CV163=12 Wabco A2
CV163=13 Wabco AA-2 (Temp Wabco A2)
CV163=14 Wabco E-2
ALCO Bell Template Pack 3
Bells (SoundCV10):
CV164=0 ALCO Bronze Bell 004
CV164=1 ALCO Bronze Bell 007
CV164=2 ALCO Bronze Bell 009
CV164=3 ALCO Bronze Bell 012
CV164=4 ALCO Bronze Bell 013
Auto Bell:
Many Second and Third Generation locomotives have been fitted with an Automatic Bell that is triggered when the horn is blown. In MANY cases this cannot even be bypassed on modern locos. Before the FRA mandated this feature on new locomotives the bell was of course turned on and off separately. Some locomotives were delivered with a manual bell and have been converted to an automatic bell. This creates a challenge in sound file creation.
We realize that not every loco with a particular prime mover had this feature. As such we have built in an option to turn the feature on and off. We will set the default in the file to be what is most appropriate for the particular file.
To turn the feature OFF - Auto Bell OFF:
1. Remove the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 4
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 0
To turn the feature ON - Auto Bell ON:
1. ADD the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 12
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 1
Auto Bell Timer:
The Bell timer is amount of time the bell will play after the horn if the auto timer is active. The timer is broken down into 1/4 of a second increments.
CV169=4 - 1 Second
CV169=8 - 2 Seconds
CV169=12 - 3 Seconds
CV169=16 - 4 Seconds
CV169=20 - 5 Seconds - Default
Etc...
Switcher Brake Squeal Template Pack 1
Brake Squeal (SoundCV11)
CV165=0 Composition Shoe #1
CV166=1 Cast Iron Shoe #1
ALCO Air Dryer Template Pack 1
Air Dryer (SoundCV12)
CV166=0 S-1 Air Dryer 1
CV166=1 C-425 Air Dryer 1
CV166=2 RS-18 Air Dryer 1
CV166=3 RS-18 Air Dryer 2 Hide description more…
H0 N XL L M4
- Article numbers
- S0825
- Last change
- 8/27/2021
- Manufacturer
- ESU
License Agreement
1. GRANT OF LICENSE
1.1 ESU grants you a non-transferable, limited, non-exclusive right to use the Content solely for your own personal purposes. You may load the Content into RAM, as well as installation on a hard disk or other storage device on a single computer, hardware product or mobile device owned by you or under your control. The installation process may result in a copy of the Content residing on your computer, in which case, you may retain one (1) copy of the Content on your computer, provided that you retain all copyright and other proprietary notices on the copy and the copy is kept in your possession with the original.1.2 By using the Content, you shall not obtain any ownership, copyright, proprietary or other interest in or to the Content. The Content is licensed, not sold.
1.3 You are licensed to use, modify and combine the Sound Samples with sound samples provided by third parties, to create your own sound compositions which, subject to you complying with the terms of this Agreement, you are free to distribute as you wish provided that: (i) the Sound Samples have been mixed together to create an original work; (ii) individual Sound Samples are not used in isolation and (iii) the Sound Samples or derivatives are not used to create sound libraries for distribution to third parties.
2. PROHIBITED USES
Neither you, nor anyone at your direction, shall:2.1 use the Content, or any part of it, for any public performance, live broadcast or time delayed live broadcast where the Content is used unattended for commercial purposes without ESU' s prior written consent;
2.2 use the Content, or any part of it, in any competitive product;
2.3 sub-license, copy, reproduce, transmit, assign, rent, sell, lease, offer on a pay-per-play basis, distribute for money or any other consideration, or commercially exploit in any other manner or through any medium whatsoever or otherwise transfer in any way the Content or any part thereof;
2.4 manufacture and/or distribute for money or otherwise commercially exploit any product that incorporates any part of the Content. If you wish to use any part of the Content for manufacture, resale, sub-license or further distribution, you must contact ESU (and where relevant, its licensors) to enter into an appropriate agreement with ESU (and, where relevant, its licensors);
2.5 publish the results of any analysis or comparative evaluation of the Content or any part thereof without ESU' s prior written consent;
2.6 reverse engineer, recompile or disassemble any part of the Content except to the extent and in the circumstances expressly permitted by ESU and its licensors in writing or by law;
3. INTELLECTUAL PROPERTY RIGHTS
You acknowledge that all intellectual property rights in the Content are and shall remain vested in ESU and its licensors. You undertake not to interfere with or diminish, whether by act or omission, the rights, title and interest in the Content of ESU and its licensors. You may be held responsible by ESU and/or any of its licensors for any infringement of any intellectual property rights in the Content. For the avoidance of doubt, provided that you comply with the terms of this Agreement, ESU shall not claim ownership of the intellectual property rights in any compositions created by your use of the Content.4. TERM AND TERMINATION
This Agreement is effective from the first date you install the Content. The rights granted to you under this Agreement shall terminate if you fail to abide by its terms. Upon such termination you agree to destroy the Content including any Content stored on the hard disk of any computer under your control. You may terminate this Agreement at any time by destroying or erasing all your copies of the Content. Any termination of this Agreement (howsoever occasioned) shall not affect any accrued rights or liabilities of you or ESU nor shall it affect the coming into force or the continuance in force of the provisions of Clauses 2, 3, 5 and 6 and any provision hereof which is by implication intended to come into or continue in force on or after such termination.5. NO WARRANTIES
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ESU AND ITS LICENSORS PROVIDE THE CONTENT "AS IS" AND ESU EXCLUDES ON BEHALF OF ITSELF AND ITS LICENSORS, ALL CONDITIONS, TERMS, REPRESENTATIONS (OTHER THAN FRAUDULENT REPRESENTATIONS) AND WARRANTIES RELATING TO THE CONTENT, WHETHER IMPOSED BY STATUTE OR BY OPERATION OF LAW OR OTHERWISE, INCLUDING BUT NOT LIMITED TO, IMPLIED WARRANTIES OF SATISFACTORY QUALITY AND FITNESS FOR A PARTICULAR PURPOSE. NEITHER ESU NOR ITS LICENSORS WARRANT THAT THE OPERATION OF THE CONTENT WILL BE UNINTERRUPTED, ERROR FREE, VIRUS FREE OR MEET YOUR SPECIFIC REQUIREMENTS. YOU MAY HAVE OTHER RIGHTS THAT VARY FROM JURISDICTION TO JURISDICTION.6. ESU's LIABILITY
Neither ESU nor its licensors shall have any liability to you for any loss or damage caused directly or indirectly in connection with the Content, any part thereof or this Agreement, except to the extent that such liability cannot be lawfully excluded. In any case, neither ESU nor its licensors shall be liable for any loss of business, data, profits, savings, or any other special, incidental, consequential, indirect or economic loss whatsoever even if such losses were contemplated at the date of this Agreement.7. GENERAL
7.1 You acknowledge that damages alone might be insufficient remedy for any breach of the terms of this Agreement and that the remedies of injunction, specific performance or other equitable relief would be suitable remedies in the event of any breach or threatened breach of this Agreement.7.2 You may not assign or otherwise transfer all or any part of this Agreement or the rights granted to you hereunder.
7.3 ESU is not obliged to provide any maintenance, technical support or upgrades to you.
7.4 You agree to comply with all applicable import and export regulations and acknowledge that you have the responsibility for obtaining all necessary licenses to export, re-export, transfer or import the Content.
7.5 This Agreement constitutes the entire agreement between you and ESU with respect to the subject matter hereof and supersedes all prior agreements, arrangements and understandings between the parties and constitutes the entire agreement between the parties relating to such subject matter hereof. No addition to or modification of any provision of this Agreement shall be binding upon ESU and you unless made by a written instrument signed by a duly authorized representative of ESU and you.
7.6 No forbearance, delay or indulgence by either party in enforcing the provisions of this Agreement shall prejudice or restrict the rights of that party nor shall any waiver of its rights operate as a waiver of any subsequent breach and no right, power or remedy herein conferred upon or reserved for either party is exclusive of any other right, power or remedy available to that party and each such right, power or remedy shall be cumulative.
7.7 Notwithstanding that the whole or any part of any provision of this Agreement may prove to be illegal or unenforceable the other provisions of this Agreement and the remainder of the provision in question shall remain in full force and effect.
If you download the designated file, you agree to be legally bound by the license given above.