")}("width","220px",["/lib/bootstrap-select/css/bootstrap-select.min.css"],"rel=\u0022stylesheet\u0022 ");
The Siemens Charger is a family of diesel-electric passenger locomotives designed and manufactured by Siemens Mobility for the North American market. There are four models of Chargers: the SC-44 for state-supported inter-city services, the SCB-40 for Brightline inter-city service, the SC-42 for VIA corridor service, and the ALC-42 for Amtrak long distance service.
The first production SC-44 was unveiled on March 26, 2016, and entered revenue service on August 24, 2017, followed by the SCB-40, which inaugurated Brightline service on January 13, 2018. The first ALC-42 was delivered to Amtrak on June 17, 2021 and entered revenue service on February 8, 2022 on the Empire Builder.
The Charger is powered by a Cummins 16-cylinder QSK95 4-stroke high speed diesel engine, which meets EPA Tier IV emissions standards that took effect in 2015.[4] Power output varies by model: the SCB-40 produces 4,000 hp (3,000 kW),[5][6] the SC-44 produces 4,400 hp (3,300 kW), and both the SC-42 and ALC-42 produce 4,200 hp (3,100 kW).[7][8] The maximum speed in service is 125 mph (201 km/h).[9]
The locomotive shares much of its overall design with the Siemens Vectron diesel and electric locomotives used in Europe and the Siemens ACS-64 electric locomotive built for Amtrak and SEPTA.
Recorded from a Siemens ALC-42 and SC-42
This project is a normal idle version. It has a single late (silenced) exhaust stack.
File also contains an "Isolation Switch" Mode on F15 when Standing Still.
Pressing F15 while not moving will lower the prime mover and lock the motor. F15 must be turned off to begin moving.
Another Mode is "Reverser In Center Position". When pressing F24 while stopped, the motor will lock so you can throttle through the notches like the prototype in neutral. F24 must be turned off to begin moving.
You can still use F26 and F27 for manual notching. You have to keep both F26 and F27 off before pressing F28 to turn on manual notching. Once F28 is on, you can use F26 to notch up and F27 to notch down. F26, F27, and F28 must be turned off to return to normal mode.
This project has "Load" mode. When turning on F29 with F15, F24, F26, F27, F28 off, the prime mover goes into load mode. While you are using load mode, the prime mover will notch up 1 or more notches based on primary load settings(CV104). The throttle notches up using speed instead of requested speed while using the load feature. F29 must be turned off to return to normal mode.
Please note: This file has a few special settings from our default retail file settings
This file has a Special feature providing the sounds and operation of the Head End Power unit. This is used on the prototype loco to provide electricity to the coaches as these locos are almost always used in passenger service.
To engage HEP you must be stopped in Idle. Pressing F7 (Shift 2) will engage the HEP unit.
The lighting has been modified to represent the lighting on the prototype.
This includes LED ditchlights that are timed to the prototype. They also do not fade in and fade out like the prototype.
The function mapping has been set to include the HEP, and special lighting of the models on the market. Including: Strobe Lights, Red Marker Lights, and Carbody Interior Lighting.
The ALC-42 and SC-42 have the ability to play the horn with Full Air, or Half Air. We have included the Full Air Horns on F2, and the Half Air Horn on F3. CV163 will change between them. Only the horns recorded from the ALC-42 have this feature. CV163 at a value of 4 or above will play the ALC-42 Half Air K5LA on F3.
ALC-42 Horn Pack 1
Horns (SoundCV9):
CV163=0 Nathan K-5LA AMTK ALC-42 Full Air and Half Air
CV163=1 Kockum Sonics Tyfon MKTH 75-5 Chime CA VIA SC-42 Full Air and Half air.
CV163=2 Nathan K-5LA AMTK ALC-42 Ed2 Full Air and Half air.
CV163=3 Kockum Sonics Tyfon MKTH 75-5 Chime CA VIA SC-42 Ed2 Full Air and Half air.
CV163=4 Nathan K-5LA
CV163=5 Nathan K-5LA-R24
CV163=6 Nathan K-5L-LA
CV163=7 Nathan K-5LA Amtrak
The Horns below will play on the Sequencer using F23
CV163=0 Nathan K-5LA AMTK ALC-42
CV163=1 Kockum Sonics Tyfon MKTH 75-5 Chime CA VIA SC-42
CV163=2 Nathan K-5LA AMTK ALC-42 Ed2
CV163=3 Kockum Sonics Tyfon MKTH 75-5 Chime CA VIA SC-42 Ed2
CV163=4 Nathan K-5LA
CV163=5 Nathan K-5LA-R24
CV163=6 Nathan K-5L-LA
CV163=7 Nathan K-5LA Amtrak
As a note, VIA RAIL ALC42s do not have a grade crossing sequencer on the floor. There is a button that plays the horn on the floor, but is the same as the horn on the console. While we have included them in the sequencer pack above, we realize this is not prototypical on those locomotives.
ALC-42 Auto Bell On/Off Trigger Template Pack 1
Bells (SoundCV10):
CV164=0 Graham-White E-Bell 010
CV164=1 Graham-White E-Bell 001
CV164=2 Graham-White E-Bell 002
CV164=3 Graham-White E-Bell 003
Auto Bell:
Many Second and Third Generation locomotives have been fitted with an Automatic Bell that is triggered when the horn is blown. In MANY cases this cannot even be bypassed on modern locos. Before the FRA mandated this feature on new locomotives the bell was of course turned on and off separately. Some locomotives were delivered with a manual bell and have been converted to an automatic bell. This creates a challenge in sound file creation.
We realize that not every loco with a particular prime mover had this feature. As such we have built in an option to turn the feature on and off. We will set the default in the file to be what is most appropriate for the particular file.
To turn the feature OFF - Auto Bell OFF:
1. Remove the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 4
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 0
To turn the feature ON - Auto Bell ON:
1. ADD the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 12
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 1
Auto Bell Timer:
The Bell timer is amount of time the bell will play after the horn if the auto timer is active. The timer is broken down into 1/4 of a second increments.
CV169=4 - 1 Second
CV169=8 - 2 Seconds
CV169=12 - 3 Seconds
CV169=16 - 4 Seconds
CV169=20 - 5 Seconds - Default
Etc...
3rd Gereration Brake Squeal Template Pack 1
Brake Squeal (SoundCV11)
CV165=0 Composition Shoe #1
CV166=1 Composition Shoe #2
Beschreibung ausblenden mehr…
Mit dem Herunterladen der gewünschten Datei stimmen sie ausdrücklich den oben genannten Lizenzbedingungen zu.