")}("width","220px",["/lib/bootstrap-select/css/bootstrap-select.min.css"],"rel=\u0022stylesheet\u0022 ");
After Millenium the German State Railway (DB) need to order new locos to replace old fashioned shunting locos of Classes 362 - 365 (former BR V60) and 290 - 295 (former BR V90). The German Voith Turbo Lokomotivtechnik GmbH & Co KG developed the BR261 diesel locomotive. The prime mover of version 10BB is MTU 8V 4000 R42 and develops 1000 kW at 1800 rpm. With a maximum speed of 100 km/h and a tractive power of 258 kN the BR261 is used in heavy shunting service as well as for mid range freight more…
For heavy switching and freight service German State Railway DB ordered 31 samples of diesel hydraulic Voith-Gravita® loco. Prime mover MTU 12V 4000 R43L delivers 1800 kW at 1800 rpm and enables the loco to reach a maximum speed of 100 km/h. Also loco rental service Northrail and HzL in Southern Germany bought two samples each.
The Prussian P8, built from 1906, was perhaps the best-known German steam locomotive series. Its designer Robert Garbe even wanted to see it used in express train service, but approval for 110 km/h failed due to its rough running at high speeds. The 1,180 hp two-cylinder locomotives reached 100 km/h and were considered undemanding and reliable pulling horses for passenger trains. They also proved their worth in front of light and fast freight trains. Of the 3,444 examples that were built for more…
The Bavarian P3/5 H (later BR 38.4) from 1921 is considered a successful design, but with only 80 units built, it was not nearly as widespread as its Prussian counterpart, the P8. Manufacturer J.A. Maffei took over the four-cylinder engine from its predecessor, the P3/5 N, but designed the three-coupler as a superheated steam locomotive. In combination with the wheel diameter of 1640 mm, the 1200 hp locomotive, later known as the BR 38.4, reached a top speed of 90 km/h. Due to its impressive more…
For the heavy express train service in the hill country, the Prussian KPEV had a four-coupled three-cylinder locomotive developed instead of replicating the proven Saxon XX HV with four cylinders. Borsig's design was then implemented, although the required maximum axle load of 17 t was exceeded by almost 2 t, meaning the locomotive could only be used on a few routes. With its output of 1,620 hp, it reached a top speed of 110 km/h. When most of the main routes were upgraded for an axle load of more…
In order to determine the suitability of the different drives for heavy freight service, the German Deutsche Reichsbahn-Gesellschaft DRG included five-coupled tender locomotives with two and three cylinders in its standard locomotive program. In 1927, ten of each type were initially built. A further 35 of the 43 with two cylinders followed in 1928. In comparison, the two-cylinder locomotive proved to be equal to the three-cylinder locomotive known as the 44 series up to the medium power range more…
In the mid-1950s, the boilers of the BR50 standard locomotives of the Deutsche Reichsbahn DR had reached the end of their service life due to the use in heavy freight traffic. Since the DR was unable to obtain replacements for its 50s, which were universally applicable with an axle load of just 15 t, in the foreseeable future, it was decided to reconstruct many locomotives with a boiler largely equivalent to that of the new BR 23 locomotive. From 1957, the DR reconstructed a total of 208 more…
In the mid-1950s, the boilers of the BR50 standard locomotives of the Deutsche Reichsbahn DR had reached the end of their service life due to the use in heavy freight traffic. Since the DR was unable to obtain replacements for its 50s, which were universally applicable with an axle load of just 15 t, in the foreseeable future, it was decided to reconstruct many locomotives with a boiler largely equivalent to that of the new BR 23 locomotive. From 1957, the DR reconstructed a total of 208 more…