")}("width","220px",["/lib/bootstrap-select/css/bootstrap-select.min.css"],"rel=\u0022stylesheet\u0022 ");
MPXpress is a series of diesel-electric passenger train locomotives designed for commuter rail service. The locomotives are built by MotivePower, a subsidiary of Wabtec. There are five variants of the MPXpress: MP36PH-3S, MP36PH-3C, MP40PH-3C, MP32PH-Q, and MP54AC. Of these, only the MP54AC conforms to federal Tier 4 emissions standards, making it the only variant that can be sold in the United States. Wabtec no longer lists the MPXpress in its locomotive portfolio.[2]
The MPXpress line of locomotives were the first production passenger locomotives to meet FRA safety regulations regarding crashworthiness and fire safety. The line also meets APTA crashworthiness standards.
Production of the locomotives have kept pace with increasingly stringent emissions regulations from the United States Environmental Protection Agency (EPA). Between 2002 and 2015, the EPA has issued four "tiers" of emissions standards and in each case the MPXpress was the first (and in some cases, only) passenger locomotive to meet the standard.
Numerous public transit agencies in Canada and the United States have ordered MPXpress locomotives for their commuter rail services. GO Transit is currently the largest client for MPI MPXpress locomotives, with 93 in their fleet.
The prime mover used in the MP36PH-3C is a EMD 16-645F3B. The Prototype has a seperate HEP unit for providing Power to the Passengers. This sound is also available in the in this file as a user dependant function that can turned on and off as needed. (Usually if 2 engines are used only the engine closest to the cars will have the HEP unit running)
These Locomotives are used Daily in "Push-Pull" service and are set up to do so as default in this decoder as well. Operating Front and rear red lights and Headlight/Ditchlights are set accordingly as default.
This project has a notch based low idle. It has a single late (silenced) exhaust stack.
File also contains an "Isolation Switch" Mode on F15 when Standing Still.
Pressing F15 while not moving will lower the prime mover and lock the motor. F15 must be turned off to begin moving.
Another Mode is "Reverser In Center Position". When pressing F24 while stopped, the motor will lock so you can throttle through the notches like the prototype in neutral. F24 must be turned off to begin moving.
This project has "Run 8" mode. When turning on F26 with F28 off, the prime mover goes to run 8. Turning off F26 returns the prime mover sounds back to normal mode.
This project has "Coast" mode. When turning on F27 with F28 off, the prime mover goes to idle for coasting purposes. Turning off F27 returns the prime mover sounds back to normal mode.
You can still use F26 and F27 for manual notching. You have to keep both F26 and F27 off before pressing F28 to turn on manual notching. Once F28 is on, you can use F26 to notch up and F27 to notch down. F26, F27, and F28 must be turned off to return to normal mode.
This project has "Load" mode. When turning on F29 with F15, F24, F26, F27, F28 off, the prime mover goes into load mode. While you are using load mode, the prime mover will notch up 1 or more notches based on primary load settings(CV104). The throttle notches up using speed instead of requested speed while using the load feature. F29 must be turned off to return to normal mode.
This file has a Special feature providing the sounds and operation of the Head End Power unit. This is used on the prototype loco to provide electricity to the coaches as these locos are almost always used in passenger service.
To engage HEP you must be stopped in Idle. Pressing F26 (Shift 2) will engage the HEP unit and allow the prime mover to run at a higher RPM.
When in stations often the engineer will go into Standby mode to preserve fuel and to allow the noise levels to come down a little. Pressing F27 on the throttle once HEP has already been engaged will allow the prime mover to come down a little. Again this can only be done while sitting still as on the prototype there is not enough RPM to provide power to the coaches and traction motors at the same time in Standy Mode.
This file is also equipped with a Smart Start feature that cycles the prime mover on and off at intervals of your choice if the throttle is left at Idle and the loco is stopped.
Smart Start (Sound CV14):
CV168=0 No Smart Start Cycle - Default
CV168=1 - 3 Minute Cycle
CV168=2 - 6 Minute Cylcle
CV168=3 - 9 Minute Cylcle
CV168=4 - 12 Minute Cylcle
Etc.....
CV168=255 - 765 Minute Cycle
M36PH-3C Horn Pack 1
Horns (SoundCV9):
CV163=0 Nathan K-5LA (AMTK ALC-42)
CV163=1 Nathan C-5A-CWP
CV163=2 Nathan P-2
CV163=3 Nathan K-3LA
CV163=4 Nathan K-12
CV163=5 Nathan P-5A
CV163=6 Nathan K-5LA (AMTK ALC-42) Ed2
CV163=7 Nathan P-2-R2
CV163=8 Nathan K-5LA (NJT)
CV163=9 Nathan P-5
CV163=10 Nathan K-5LA (Metra)
CV163=11 Nathan K-2H
CV163=12 Nathan K-5LA (MARC)
CV163=13 Nathan K-3L
CV163=14 Nathan K5-CA-LS Horn
CV163=15 Nathan K5-CA-LS Half Air Horn
SD40-3 Bell Template Pack 1
Bells (SoundCV10):
CV164=0 Graham-White E-Bell 006
CV164=1 Graham-White E-Bell 009
CV164=2 Graham-White E-Bell 001
CV164=3 Graham-White E-Bell 004
CV164=4 Transtronic E-Bell 001
CV164=5 Ekyrail E-Bell 001
Auto Bell:
Many Second and Third Generation locomotives have been fitted with an Automatic Bell that is triggered when the horn is blown. In MANY cases this cannot even be bypassed on modern locos. Before the FRA mandated this feature on new locomotives the bell was of course turned on and off separately. Some locomotives were delivered with a manual bell and have been converted to an automatic bell. This creates a challenge in sound file creation.
We realize that not every loco with a particular prime mover had this feature. As such we have built in an option to turn the feature on and off. We will set the default in the file to be what is most appropriate for the particular file.
To turn the feature OFF - Auto Bell OFF:
1. Remove the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 4
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 0
To turn the feature ON - Auto Bell ON:
1. ADD the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 12
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 1
Auto Bell Timer:
The Bell timer is amount of time the bell will play after the horn if the auto timer is active. The timer is broken down into 1/4 of a second increments.
CV169=4 - 1 Second
CV169=8 - 2 Seconds
CV169=12 - 3 Seconds
CV169=16 - 4 Seconds
CV169=20 - 5 Seconds - Default
Etc...
3rd Gereration Brake Squeal Template Pack 1
Brake Squeal (SoundCV11)
CV165=0 Composition Shoe #1
CV165=1 Composition Shoe #2
EMD 3rd Generation Air Dryer Template Pack 1
Air Dryer (SoundCV12)
CV166=0 GP60 Air Dryer 1
CV166=1 SD60E Air Dryer 2
CV166=2 SD70M-2 Air Dryer 3
CV166=3 SD70MAC Air Dryer 4 Hide description more…
The MPXpress line of locomotives were the first production passenger locomotives to meet EPA Tier 1 and Tier 2 emissions regulations, as well as FRA safety regulations regarding crashworthiness and fire safety. Numerous public transit agencies in Canada and the United States have ordered MPXpress locomotives for their commuter rail services. To date only GO Transit have MP40PH-3C in Service but Sounder Commutr Rail in Seattle does have an order pending for 3 Units.
The prime mover used in the MP40PH-3C is a EMD 16-710GB. The Prototype has a seperate HEP unit for providing Power to the Passengers. This sound is also available in the in this file as a user dependant function that can turned on and off as needed. (Usually if 2 engines are used only the engine closest to the cars will have the HEP unit running)
These Locomotives are used Daily in "Push-Pull" service and are set up to do so as default in this decoder as well. Operating Front and rear red lights and Headlight/Ditchlights are set accordingly as default.
True Line Trains has produced a Fantastic HO model Of the MP40PH-3C and comes factory equipped with an ESU LokSound Select decoder. This file is used in the Model. Hide description more…
The American Locomotive Company's model 244 prime mover was developed during the mid-1940s to power its post-war diesel locomotives. Interestingly, while Alco helped pioneer diesel technology dating back to the 1920s it had difficulty truly competing against Electro-Motive-Division due to reliability issues with its diesel engines. Before Alco began implementing the 244 in its locomotives the builder had spent most of the 1930s developing an earlier model that was used in most of its early switchers. The new prime mover was supposed to usher in a new era for Alco but instead saw it slip further behind EMD in the marketplace. During the early 1950s the manufacturer replaced the engine with the more reliable 251 that powered its Century series. It would prove to be the company's last engine as it exited the market before 1970.
This sound file would be appropriate for the following locomotives:
RS-2, RS-3, RSC-2, RSC-3, RSD-4, RSD-5
Although there are slight differences, this sound file could also be used in the following locomotives:
FA-1, FB-1, FA-2, FB-2, FPA-2, FPB-2
Recorded from a ALCO RS-3
This project is a normal idle version. It has a single exhaust stack.
File also contains an "Isolation Switch" Mode on F15 when Standing Still.
Pressing F15 while not moving will lower the prime mover and lock the motor. F15 must be turned off to begin moving.
Another Mode is "Reverser In Center Position". When pressing F24 while stopped, the motor will lock so you can throttle through the notches like the prototype in neutral. F24 must be turned off to begin moving.
This project has "Run 8" mode. When turning on F26 with F28 off, the prime mover goes to run 8. Turning off F26 returns the prime mover sounds back to normal mode.
This project has "Coast" mode. When turning on F27 with F28 off, the prime mover goes to idle for coasting purposes. Turning off F27 returns the prime mover sounds back to normal mode.
You can still use F26 and F27 for manual nothing. You have to keep both F26 and F27 off before pressing F28 to turn on manual notching. Once F28 is on, you can use F26 to notch up and F27 to notch down. F26, F27, and F28 must be turned off to return to normal mode.
This project has "Load" mode. When turning on F29 with F15, F24, F26, F27, F28 off, the prime mover goes into load mode. While you are using load mode, the prime mover will notch up 1 or more notches based on primary load settings(CV104). The throttle notches up using speed instead of requested speed while using the load feature. F29 must be turned off to return to normal mode.
1st Generation Switcher Horn Pack 1
Horns (SoundCV9):
CV163=0 Handcock 4700 Whistle
CV163=1 Leslie A-125
CV163=2 Leslie A-200
CV163=3 Wabco E2
CV163=4 Leslie S-2M
CV163=5 Nathan K3L
CV163=6 Leslie S-3L
CV163=7 Nathan M-3
CV163=8 Nathan M-5
CV163=9 Nathan P-2
CV163=10 Nathan P-3-OC
CV163=11 Nathan P-5-OC
CV163=12 Wabco A2
CV163=13 Nathan K3H
CV163=14 Wabco E-2
CV163=15 Leslie S5T
ALCO Bell Template Pack 3
Bells (SoundCV10):
CV164=0 ALCO Bronze Bell 004
CV164=1 Steam Loco Pnumatic Bell
CV164=2 ALCO Bronze Bell 009
CV164=3 ALCO Bronze Bell 012
CV164=4 ALCO Bronze Bell 013
Auto Bell:
Many Second and Third Generation locomotives have been fitted with an Automatic Bell that is triggered when the horn is blown. In MANY cases this cannot even be bypassed on modern locos. Before the FRA mandated this feature on new locomotives the bell was of course turned on and off separately. Some locomotives were delivered with a manual bell and have been converted to an automatic bell. This creates a challenge in sound file creation.
We realize that not every loco with a particular prime mover had this feature. As such we have built in an option to turn the feature on and off. We will set the default in the file to be what is most appropriate for the particular file.
To turn the feature OFF - Auto Bell OFF:
1. Remove the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 4
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 0
To turn the feature ON - Auto Bell ON:
1. ADD the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 12
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 1
Auto Bell Timer:
The Bell timer is amount of time the bell will play after the horn if the auto timer is active. The timer is broken down into 1/4 of a second increments.
CV169=4 - 1 Second
CV169=8 - 2 Seconds
CV169=12 - 3 Seconds
CV169=16 - 4 Seconds
CV169=20 - 5 Seconds - Default
Etc...
Switcher Brake Squeal Template Pack 1
Brake Squeal (SoundCV11)
CV165=0 Composition Shoe #1
CV166=1 Cast Iron Shoe #1
ALCO Air Dryer Template Pack 1
Air Dryer (SoundCV12)
CV166=0 S-1 Air Dryer 1
CV166=1 C-425 Air Dryer 1
CV166=2 RS-18 Air Dryer 1
CV166=3 RS-18 Air Dryer 2 Hide description more…
Bowser RS-3 Long Hood Forward Version
The American Locomotive Company's model 244 prime mover was developed during the mid-1940s to power its post-war diesel locomotives. Interestingly, while Alco helped pioneer diesel technology dating back to the 1920s it had difficulty truly competing against Electro-Motive-Division due to reliability issues with its diesel engines. Before Alco began implementing the 244 in its locomotives the builder had spent most of the 1930s developing an earlier model that was used in most of its early switchers. The new prime mover was supposed to usher in a new era for Alco but instead saw it slip further behind EMD in the marketplace. During the early 1950s the manufacturer replaced the engine with the more reliable 251 that powered its Century series. It would prove to be the company's last engine as it exited the market before 1970.
This sound file would be appropriate for the following locomotives:
RS-2, RS-3, RSC-2, RSC-3, RSD-4, RSD-5
Although there are slight differences, this sound file could also be used in the following locomotives:
FA-1, FB-1, FA-2, FB-2, FPA-2, FPB-2
Recorded from a ALCO RS-3
This project is a normal idle version. It has a single exhaust stack.
File also contains an "Isolation Switch" Mode on F15 when Standing Still.
Pressing F15 while not moving will lower the prime mover and lock the motor. F15 must be turned off to begin moving.
Another Mode is "Reverser In Center Position". When pressing F24 while stopped, the motor will lock so you can throttle through the notches like the prototype in neutral. F24 must be turned off to begin moving.
This project has "Run 8" mode. When turning on F26 with F28 off, the prime mover goes to run 8. Turning off F26 returns the prime mover sounds back to normal mode.
This project has "Coast" mode. When turning on F27 with F28 off, the prime mover goes to idle for coasting purposes. Turning off F27 returns the prime mover sounds back to normal mode.
You can still use F26 and F27 for manual nothing. You have to keep both F26 and F27 off before pressing F28 to turn on manual notching. Once F28 is on, you can use F26 to notch up and F27 to notch down. F26, F27, and F28 must be turned off to return to normal mode.
This project has "Load" mode. When turning on F29 with F15, F24, F26, F27, F28 off, the prime mover goes into load mode. While you are using load mode, the prime mover will notch up 1 or more notches based on primary load settings(CV104). The throttle notches up using speed instead of requested speed while using the load feature. F29 must be turned off to return to normal mode.
1st Generation Switcher Horn Pack 1
Horns (SoundCV9):
CV163=0 Handcock 4700 Whistle
CV163=1 Leslie A-125
CV163=2 Leslie A-200
CV163=3 Wabco E2
CV163=4 Leslie S-2M
CV163=5 Nathan K3L
CV163=6 Leslie S-3L
CV163=7 Nathan M-3
CV163=8 Nathan M-5
CV163=9 Nathan P-2
CV163=10 Nathan P-3-OC
CV163=11 Nathan P-5-OC
CV163=12 Wabco A2
CV163=13 Nathan K3H
CV163=14 Wabco E-2
CV163=15 Leslie S5T
ALCO Bell Template Pack 3
Bells (SoundCV10):
CV164=0 ALCO Bronze Bell 004
CV164=1 Steam Loco Pnumatic Bell
CV164=2 ALCO Bronze Bell 009
CV164=3 ALCO Bronze Bell 012
CV164=4 ALCO Bronze Bell 013
Auto Bell:
Many Second and Third Generation locomotives have been fitted with an Automatic Bell that is triggered when the horn is blown. In MANY cases this cannot even be bypassed on modern locos. Before the FRA mandated this feature on new locomotives the bell was of course turned on and off separately. Some locomotives were delivered with a manual bell and have been converted to an automatic bell. This creates a challenge in sound file creation.
We realize that not every loco with a particular prime mover had this feature. As such we have built in an option to turn the feature on and off. We will set the default in the file to be what is most appropriate for the particular file.
To turn the feature OFF - Auto Bell OFF:
1. Remove the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 4
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 0
To turn the feature ON - Auto Bell ON:
1. ADD the Auto bell sound slot from the function mapping chart
CV31 = 16, CV32 = 8
----------------------
CV311 = 12
2. Change the sound configuration of the Auto bell sound slot
CV31 = 16, CV32 = 1
----------------------
CV287 = 1
Auto Bell Timer:
The Bell timer is amount of time the bell will play after the horn if the auto timer is active. The timer is broken down into 1/4 of a second increments.
CV169=4 - 1 Second
CV169=8 - 2 Seconds
CV169=12 - 3 Seconds
CV169=16 - 4 Seconds
CV169=20 - 5 Seconds - Default
Etc...
Switcher Brake Squeal Template Pack 1
Brake Squeal (SoundCV11)
CV165=0 Composition Shoe #1
CV166=1 Cast Iron Shoe #1
ALCO Air Dryer Template Pack 1
Air Dryer (SoundCV12)
CV166=0 S-1 Air Dryer 1
CV166=1 C-425 Air Dryer 1
CV166=2 RS-18 Air Dryer 1
CV166=3 RS-18 Air Dryer 2 Hide description more…
The various railcars Talent are often called the “regional ICE” because of the way they look. The front ends of the ICE and Talent are very similar in looks, which is probably no accident, because an appealing appearance is always a good sales argument. 644 series diesel-electric railcars were delivered before the diesel-mecha-nical 643 series “Talents”. They are designed for municipal railway services around Cologne and have 1,000 kW engine power (compared with the 643’s 570 kW). In combination with electric power transmission, this enables very good acceleration of 1.0 m/s, and the top speed of 120 km/h matches that of the 643. The 644s are almost 4 m longer and have twice as many doors as the 643 to ensure smooth passenger flows. Hide description more…
Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.4.21 or newer
The emd 645 series was an evolution of the earlier 567 series and a precursor to the later 710 series. When the 645 prime mover entered production in 1965, a large series of new locomotive models was introduced. The turbocharged version was used in EMD's 40 Series (GP40, SD40 and SD45) in 3,000 horsepower (2,200 kW), sixteen-cylinder form and in 3,600 horsepower (2,700 kW), twenty-cylinder form. EMD also introduced the Roots-blown 38 Series (GP38, SD38) and turbocharged, twelve-cylinder 39 Series (GP39, SD39). All of these locomotive models extensively share common components and subsystems, thereby significantly reducing cost and increasing interchangeability. The GP38-2 and SD40-2 became the most popular models of the series and among the most popular locomotive models ever built.
This 16cyl 645E3 with Turbo sound file would be appropriate for the following locomotives:
GP40
GP40P
GP40P-2
GP40-2
GP40X
SD40X
SD40A
SD45T-2
SD40-2
SD40-2W
SD40-2S
F40C
F40PH
F40PH-2
F40PH-2M
SDP40F
SD40-2F
Export locomotives:
GT26MC
GT26CW
GT26CW-1
GT26CW-2
GT26CU-2
Please note:
This file contains a "Class Light" feature which allows for Cycling Aux3, Aux4, and Aux5 when using a 21MTC decoder. Assign the "Class Light" "Sound" to the function button of your choice and and be sure each Aux listed above is set to "Dimmable Headlight".
As with all SELECT decoders there are up to 16 separate horns, 2 separate brake squeals and 2 bells included on this one sound profile! All changeable using CV48.
Prime Mover:
CV48=0 EMD 16cyl 645E3
Uses our INTERMEDIATE-HORNS-AND-BELLS template...
Horns:
CV48=0 Nathan K5LA
CV48=1 Nathan K3L
CV48=2 Nathan M5
CV48=3 Nathan P3
CV48=4 Nathan Old Cast P5
CV48=5 Nathan K3H
CV48=6 Leslie RS3L
CV48=7 Leslie RS5T
CV48=8 Leslie A125
CV48=9 Nathan M3
CV48=10 Leslie RS3K
CV48=11 Nathan K5H
CV48=12 Leslie A-125
CV48=13 Nathan M3H
CV48=14 Leslie S3E
CV48=15 Leslie S5TRF
Bells:
CV48=0 EMD Steel Bell
CV48=64 EMD Bronze Bell
Add values from above for total CV48 value.
Default CV48 Value = 69
0 - EMD 16cyl 645E3
7 - Nathan K3H
64 - EMD Bronze Bell
Total 0+5+64 = 69
Please Note:
File Contains a Modern E-Bell, and MILW E-Bell and a Gong Bell which can be selected in Function Mapping. Simply choose the appropriate Sound Slot for F1.
Sound Slot 4 is the default bell (changable with CV48)
Sound Slot 9 is the Modern E-Bell
Sound Slot 22 is the MILW E-Bell
Sound Slot 23 is the Gong Bell
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/ Hide description more…
The GE "Genesis" series of Locomotives was developed to be the main locomotives for Amtrak. Amtraks EMD F40PH locomotives were aging fast and GE came to the rescue with a more powerful and more fuel efficient design. Some P42 Locomotives were built with a Dual Mode capability utilizing a 3rd Rail shoe for collecting electricity. These engines run on the North East Corridor on Amtrak and on Metro North. The ESU version is the DC model which is much more common. It can be used to represent the P42s used by Amtrak, Via, NJT and Conn DOT. It can also be used in the non-electrified Areas of Metro North.
The P42 has a Very Specific Sound set. No Generic GE sound is correct for it. We have gone out of our way to make sure the sound we provide is as accurate as possible. We’ve even had the opportunity to take a cab in a P42 and take note of exactly how the engine was operated so that we could produce a sound that is absolutely true to the prototype.
Some the P42 Specific Features include the following:
-Air Bell and E-Bell (E-Bell Default)
-Automatic E-Bell and Flashing Ditch Lights with the Horn
-Awesome LOUD K5LA Amtrak P42 Horn
-Low Idle sounds (when HEP is off)
-P42 Dynamic Brake sounds
-Accurate HEP Sounds with the Prime Mover running about 900 RPM
-Change in sound when HEP is active an heavy load is applied
-Stand By Mode when HEP is active and sitting still (on a function button)
-Auto Crossing Sequence loop with Bell and Flashing Ditch Lights (Real P42's have a button on the floor to activate this!)
-Air Dryer sound
-Outstanding "Whoop" Air compressor sounds
-Function outputs AUX 1 and AUX 2 set up for Reversing Red Lights on nose and tail with ability to be turned off separate from the Headlights for prototypical running.
-Function outputs AUX 3 and AUX 4 are set up for Flashing Ditch Lights Hide description more…
Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.4.21 or newer
V2-Second Version of the is Popular Prime mover!
The emd 645 series was an evolution of the earlier 567 series and a precursor to the later 710 series. When the 645 prime mover entered production in 1965, a large series of new locomotive models was introduced. The turbocharged version was used in EMD's 40 Series (GP40, SD40 and SD45) in 3,000 horsepower (2,200 kW), sixteen-cylinder form and in 3,600 horsepower (2,700 kW), twenty-cylinder form. EMD also introduced the Roots-blown 38 Series (GP38, SD38) and turbocharged, twelve-cylinder 39 Series (GP39, SD39). All of these locomotive models extensively share common components and subsystems, thereby significantly reducing cost and increasing interchangeability. The GP38-2 and SD40-2 became the most popular models of the series and among the most popular locomotive models ever built.
This 16cyl 645E3 with Turbo sound file would be appropriate for the following locomotives:
GP40
GP40P
GP40P-2
GP40-2
GP40X
SD40X
SD40A
SD45T-2
SD40-2
SD40-2W
SD40-2S
F40C
F40PH
F40PH-2
F40PH-2M
SDP40F
SD40-2F
Export locomotives:
GT26MC
GT26CW
GT26CW-1
GT26CW-2
GT26CU-2
Please note:
This file contains a "Class Light" feature which allows for Cycling Aux3, Aux4, and Aux5 when using a 21MTC decoder. Assign the "Class Light" "Sound" to the function button of your choice and and be sure each Aux listed above is set to "Dimmable Headlight".
File also contains a "low Idle" Mode on F4 when Standing Still.
Pressing F4 while not moving will lower the prime mover and lock the motor. F4 must be turned off to go to "regular idle" and begin moving.
Once moving, F4 becomes the Dynamic Brake.
As with all SELECT decoders there are up to 16 separate horns, 2 separate brake squeals and 2 bells included on this one sound profile! All changeable using CV48.
Prime Mover:
CV48=0 EMD 16cyl 645E3
Uses our INTERMEDIATE-HORNS-AND-BELLS template...
Horns:
CV48=0 Nathan K5LA
CV48=1 Nathan K3L
CV48=2 Nathan M5
CV48=3 Nathan P3
CV48=4 Nathan Old Cast P5
CV48=5 Nathan K3HA
CV48=6 Leslie RS3L
CV48=7 Leslie RS5T
CV48=8 Leslie A125
CV48=9 Nathan M3
CV48=10 Leslie RS3K
CV48=11 Nathan K5H
CV48=12 Leslie A-125
CV48=13 Nathan M3H
CV48=14 Leslie S3E
CV48=15 Leslie S5TRF
Bells:
CV48=0 EMD Steel Bell
CV48=64 EMD Bronze Bell
Add values from above for total CV48 value.
Default CV48 Value = 71
0 - EMD 16cyl 645E3
7 - Leslie RS5T
64 - EMD Bronze Bell
Total 0+7+64 = 71
Please Note:
File Contains a Modern E-Bell, and MILW E-Bell and a Gong Bell which can be selected in Function Mapping. Simply choose the appropriate Sound Slot for F1.
Sound Slot 4 is the default bell (changable with CV48)
Sound Slot 9 is the Modern E-Bell
Sound Slot 22 is the MILW E-Bell
Sound Slot 23 is the Gong Bell
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/ Hide description more…
Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.5.1 or newer
V2-Second Version of the is Popular Prime mover!
An SD39 is a 6-axle diesel-electric locomotive built by General Motors Electro-Motive Division between August 1968 and May 1970. 54 were built for American railroads.
In 1966 EMD replaced all their old models with new ones having the new 645 diesel. These included six-axle models SD38, SD40, SDP40 and SD45; the SD39 was added in 1968. All shared standard components including the frame, cab, traction alternator, trucks, traction motors, and air brakes. The difference was the power output: SD38 = 2,000 hp (1,490 kW) from a non-turbocharged V16, SD39 = 2,300 hp (1,720 kW) from a turbocharged V12, SD40 = 3,000 hp (2,240 kW) from a turbocharged V16, and SD45 = 3,600 hp (2,680 kW) from a turbocharged V20. The SD39 had the smallest prime mover and therefore had the most unused space above the frame, inside the hood between the main generator and electrical cabinet, and outside in large end "porches".
Some SD39s had a few "Odd" features depending on the owners.
IT had Gong Bells, later N&W and B&M
MN&S had Air whistles
The SDL39 variant of the MILW and SOO Line had early Speaker type E-Bells.
We've add these "odd" items in this file.
GP39
GP39-2
SD39
SDL39
CIE 071
EMD GT22
British Rail Class 57
V/Line N class
New Zealand DFT class
JT22CW
V/Line A class
This would also be VERY close to a GP49.
Please note:
This file contains a "Class Light" feature which allows for Cycling Aux3, Aux4, and Aux5 when using a 21MTC decoder. Assign the "Class Light" "Sound" to the function button of your choice and and be sure each Aux listed above is set to "Dimmable Headlight".
File also contains a "low Idle" Mode on F4 when Standing Still.
Pressing F4 while not moving will lower the prime mover and lock the motor. F4 must be turned off to go to "regular idle" and begin moving.
Once moving, F4 becomes the Dynamic Brake.
As with all SELECT decoders there are up to 16 separate horns, 2 separate brake squeals and 2 bells included on this one sound profile! All changeable using CV48.
Prime Mover:
CV48=0 EMD 16cyl 645E3
Uses our INTERMEDIATE-HORNS-AND-BELLS template...
Horns:
CV48=0 Leslie S3L *Default*
CV48=1 Nathan K3L
CV48=2 Nathan M5
CV48=3 Nathan P3
CV48=4 Nathan Old Cast P5
CV48=5 Leslie RS3L
CV48=6 Leslie S3L*Duplicate due to space restrictions*
CV48=7 Leslie RS5T
CV48=8 Hancock Air Whistle
CV48=9 Nathan M3
CV48=10 Leslie S3L *Duplicate due to space restrictions*
CV48=11 Nathan K5H
CV48=12 Leslie S2M
CV48=13 Leslie S3L *Duplicate due to space restrictions*
CV48=14 Leslie S3L *Duplicate due to space restrictions*
CV48=15 Leslie S5TRF
Bells:
CV48=0 EMD Steel Bell
CV48=64 EMD Bronze Bell
Add values from above for total CV48 value.
Default CV48 Value = 64
0 - EMD 12cyl 645E3
0 - Leslie S3L
64 - EMD Bronze Bell
Total 0+7+64 = 71
Please Note:
File Contains a Modern E-Bell, and MILW E-Bell and a Gong Bell which can be selected in Function Mapping. Simply choose the appropriate Sound Slot for F1.
Sound Slot 4 is the default bell (changable with CV48)
Sound Slot 9 is the Modern E-Bell
Sound Slot 22 is the MILW E-Bell
Sound Slot 23 is the Gong Bell
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/ Hide description more…
Equipped with ESU "FULL THROTTLE" features!
MUST use LokProgrammer Version 4.5.1 or newer
V3-Second Version of the is Popular Prime mover!
The EMD 645 series engine was an evolution of the earlier 567 series and a precursor to the later 710 series. When the 645 prime mover entered production in 1965, a large series of new locomotive models were introduced. The turbocharged version was used in EMD's 40 Series (GP40, SD40 and SD45) in 3,000 horsepower (2,200 kW), sixteen-cylinder form and in 3,600 horsepower (2,700 kW), twenty-cylinder form. EMD also introduced the Roots-blown 38 Series (GP38, SD38) and turbocharged, twelve-cylinder 39 Series (GP39, SD39). All of these locomotive models extensively share common components and subsystems, thereby significantly reducing cost and increasing interchangeability. The GP38-2 and SD40-2 became the most popular models of the series and among the most popular locomotive models ever built.
This 16cyl 645E3 Turbo sound file with silenced exhaust would be appropriate for the following locomotives:
GP40-2
GP40X
SD40X
SD40-2
F40C
F40PH
F40PH-2
F40PH-2M
SDP40F
SD40-2F
Other appropriate locomotives without silenced exhaust that could use this file:
GP40
GP40P
GP40P-2
SD40A
SD45T-2
SD40-2W
Export locomotives:
GT26MC
GT26CW
GT26CW-1
GT26CW-2
GT26CU-2
Please note:
This file contains a "Class Light" feature which allows for Cycling Aux3, Aux4, and Aux5 when using a 21MTC decoder. Assign the "Class Light" "Sound" to the function button of your choice and and be sure each Aux listed above is set to "Dimmable Headlight".
File also contains a "low Idle" Mode on F4 when Standing Still.
Pressing F4 while not moving will lower the prime mover and lock the motor. F4 must be turned off to go to "regular idle" and begin moving.
Once moving, F4 becomes the Dynamic Brake.
As with all SELECT decoders there are up to 16 separate horns, 2 separate brake squeals and 2 bells included on this one sound profile! All changeable using CV48.
Prime Mover:
CV48=0 EMD 16cyl 645E3
Uses our INTERMEDIATE-HORNS-AND-BELLS template...
Horns:
CV48=0 Nathan K5LA
CV48=1 Nathan K3L
CV48=2 Nathan M5
CV48=3 Nathan P3
CV48=4 Nathan Old Cast P5
CV48=5 Nathan K3HA
CV48=6 Leslie RS3L
CV48=7 Leslie RS5T
CV48=8 Leslie A125
CV48=9 Nathan M3
CV48=10 Leslie RS3K
CV48=11 Nathan K5H
CV48=12 Leslie A-125
CV48=13 Nathan M3H
CV48=14 Leslie S3E
CV48=15 Leslie S5TRF
Bells:
CV48=0 EMD Steel Bell
CV48=64 EMD Bronze Bell
Add values from above for total CV48 value.
Default CV48 Value = 71
0 - EMD 16cyl 645E3
7 - Leslie RS5T
64 - EMD Bronze Bell
Total 0+7+64 = 71
Please Note:
File Contains a Modern E-Bell, and MILW E-Bell and a Gong Bell which can be selected in Function Mapping. Simply choose the appropriate Sound Slot for F1.
Sound Slot 4 is the default bell (changable with CV48)
Sound Slot 9 is the Modern E-Bell
Sound Slot 22 is the MILW E-Bell
Sound Slot 23 is the Gong Bell
New FULL THROTTLE features:
Drive Hold: Sound Slot 2 Mapped to F9
Independent Brake: Sound Slot 11 Mapped to F10
Run 8: Sound Slot 20 (not Mapped)
Coast: Sound Slot 21 (not Mapped)
For more info please see the "Full Throttle" Quick Start Guide in the ESU Instruction Manual Section of our Website.
http://www.esu.eu/en/downloads/instruction-manuals/digital-decoders/ Hide description more…
If you download the designated file, you agree to be legally bound by the license given above.